manualshive.com logo in svg

Steelcase c:scape Low Storage Series, Руководство по сборке

Поделиться
Скачать
Steelcase c:scape Low Storage Series Скачать руководство пользователя страница 4

LOCK CYLINDER ASSEMBLY

REMOVAL TOOL

LOCK 

ASSEMBLY

LOCK
CYLINDER
ASSEMBLY

Page 4 of 15

939500368 Rev K

Front Removal of Lock Cylinder

1. 

Turn lock plug to unlocked position with

conventional key.

2. 

Insert removal tool into lock cylinder.

3. 

Rotate lock cylinder assembly slightly in a

counter clockwise direction while at the same
time pulling on removal tool, thus removing the
lock cylinder from the lock assembly.

4. 

At this time the mechanism inside the lock

assembly may rotate back to the locked position
preventing the installation of new lock plug. If
this occurs, insert a flat-bladed screwdriver into
the back of lock assembly and turn clockwise
unlocking the lock assembly. Insert tool into new
lock plug assembly. Hold tool in a horizontal
position and insert new lock plug assembly into
lock assembly. It may be necessary to hold the
new plug assembly with finger while removing
tool.

DIMPLE LOCATED ON FRONT
OF LOCK CYLINDER ASSEMBLY

TOOL RK-XF

TOOL RK-FR

REMOVAL TOOL

STANDARD KEY OR MASTER KEY

LOCK SHOWN IN LOCKED POSITION

A FRONT REMOVAL
LOCK CYLINDER CAN
BE IDENTIFIED WITH
A SMALL DIMPLE
LOCATED DIRECTLY
ABOVE THE KEY SLOT 

Содержание c:scape Low Storage Series
















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды