manualshive.com logo in svg

Steelcase A5BQ, Руководство пользователя

Поделиться
Скачать
Steelcase A5BQ Скачать руководство пользователя страница 2

®

WARNING

RISK OF SERIOUS INJURY DUE TO PINCH POINTS, TIPOVER, OR POTENTIAL COLLAPSE.

This powered, adjustable height desk appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.

RISK OF DEATH OR SERIOUS INJURY.

 

                                                                   Raising or lowering desk can

trap, pinch or crush body parts or property. 

DO NOT ALLOW USE BY CHILDREN

                                                               or people unable to understand

the risks and to safely adjust the desk height. 

MAINTAIN >1” (25mm) GAP ABOVE OBJECTS ON DESK AT MAX
HIEGHT AND BETWEEN THE DESK & ADJACENT OBJECTS.
Locate desk, accessories, and nearby objects to allow movement of
desktop through full range without pulling cords, trapping body parts, 
or colliding with anything (shelves, electrical plugs and cords, door
knobs, window sills, storage cabinets, etc.)

   

CRUSH HAZARD - DO NOT PLACE FEET, LEGS OR OTHER BODY

PARTS ON OBJECTS PLACED UNDER TABLE TOP OR BELOW

MODESTY PANEL.

 

DO NOT OPERATE THIS EQUIPMENT Unless Properly Trained. 

Max.

Min.

>1"

(25mm)

>1"

(25mm)

>1"

(25mm)

X

X

X

NOTE: Desk image

is for reference only.

Table shape and leg

quantity may change

based on the style

and configuration. 

Page 2 of 35

 1/888.783.3522

www.steelcase.com

?

INSPECT REGULARLY. Stop using if product is damaged or has
loose parts. Only repair with Steelcase authorized parts and methods.

 

004231D Rev T

Содержание A5BQ




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды