Steadicam Steadimate-S Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 24

Steadicam Steadimate-S Скачать руководство пользователя страница 2

1

The Tiffen Company

90 Oser Avenue
Hauppauge, NY 11788
Visit us at

Introduction

The Steadicam

®

Steadimate-S

™

Welcome to the Steadicam family! Steadicam began stabilizing
cameras over 40 years ago, and continues to innovate solutions for
today’s cinematographers.

In combination with a Steadicam A-30 or A-15 arm, and Zephyr or
AERO vest, the new Steadimate-S greatly reduces operator fatigue
and increases operating time by carrying the system weight on the
hips through a spring arm and vest. The spring arm greatly reduces
the common bouncing image effect on the vertical axis that occurs
while walking with handheld stabilizers, allowing more natural camera

movements and smoother final shots.

Get ready to take your film making to the next level by identifying the

Steadimate-S parts, and installing them onto your handheld stabilizer!

«
1
2
3
4
...
»

Содержание Steadimate-S

























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды