Adjusting the keel of the upper cutting table
IMAGES
Information!
1.This chapter is not applicable to the model
w i t h o u t u p p e r t a b l e ( S C 3 1 0 W ,
SC390W and SLL390W).
2.You will need a slide gauge and a ruler (not
included) to carry out this adjustment.
Checking
1.Make sure that the machine is the horizontal
resting position by lowering the head and
locking it by rotating the head by means of
knob
32
.
2.Loosen knob
46
for height adjustment of the
upper table
38
.
3.Lower upper table
38
to abutment.
4.Tighten height adjusting knob
46
of the upper
table.
5.Loosen and remove fastening screws
40
and
41
of the movable guard
42
.
6.Remove guard
42
.
7.Loosen the both screws
48
.
8.Remove upper table
38
by smoothly pulling it
upwards.
9.The distance between the inside of keel
39
and
the outside of the teeth of the disk must be
between 3mm and 5mm at any visible
point.
10.If the measurements are not within the range of
the figure, proceed to adjusting.
Adjusting
1.Make sure that the machine is the horizontal
resting position by lowering the head and
locking it by rotating the head by means of
knob
32
.
2.Loosen knob
46
for height adjustment of the
upper table
38
.
3.Lower upper table
38
to abutment.
4.Tighten height adjusting knob
46
of the upper
table.
5.Loosen and remove fastening screws
40
and
41
of the movable guard
42
.
6.Remove guard
42
.
7.Loosen the both screws
48
.
8.Remove upper table
38
by smoothly pulling it
upwards.
9.Loosen the two keel adjusting screws
48
.
10.Adjust the position of the keel
48
such that the
distance between the inside of keel 39 and
the outside of the teeth of the disk must be
between 3mm and 5mm at any point.
11.Tighten the two keel adjusting screws
48
.
12.Position upper table
38
by applying it onto its
supports.
13.Tighten the two screws
48
.
14.Position movable guard
42
.
15.Tighten fastening screws
40
and
41
of the
movable guard
42
.
9. Changing tools
Attention!
This operation must be carried out with the machine
unplugged and with the disk still. Use protective
gloves.
Removal of the cutting disk
IMAGES
1.Place the head in its upper blocking position by
tilting the head upwards until abutting.
2.Immobilize flange
17
by means of the flange
wrench as delivered together with the
equipment.
3.Loosen screw
18
clockwise with the tubular
key as delivered together with the
equipment.
4.Tighten button
34
to unblock the movable guard
6
.
5.Clear guard
6
by pushing it upwards.
6.Remove flange
17
, screw
18
and washer
19
.
7.Hold cutting disk with one hand.
8.Remove flange
17
, screw
18
and washer
19
with
the other hand.
9.Remove the disk to be replaced.
Changing the cutting disk
IMAGE
1.Carefully clean sawdust and debris from the
supports, flanges and the insides of the
guards.
ENGLISH
44
44
H
I
J
K
B
A
C
A
Содержание SC3000W
