background image

9

Do not install this water heater directly on a carpeted floor. A fire 

hazard may result. Instead the water heater must be placed on a 

metal or wood panel extending beyond the full width and depth 

by  at  least  3  inches  in  any  direction.  If  the  heater  is  installed 

in  a  carpeted  alcove,  the  entire  floor  shall  be  covered  by  the 

panel. Also, see the DrAINING requirements in MAINTeNANCe 

Section.
The heater shall be located or protected so it is not subject to 

physical damage by a moving vehicle.
Flammable items, pressurized containers or any other potential 

fire hazardous articles must never be placed on or adjacent to 

the heater. Open containers or flammable material should not be 

stored or used in the same room with the heater.
The heater must not be located in an area where it will be subject 

to freezing.
locate it near a floor drain. The heater should be located in an 

area where leakage from heater or connections will not result in 

damage to adjacent area or to lower floors of the structure.
When  such  locations  cannot  be  avoided,  a  suitable  drain  pan 

should be installed under heater. Such pans should be fabricated 

with sides at least 2” deep, with length and width at least 2” greater 

than diameter of heater and must be piped to an adequate drain. 

Pan must not restrict combustion air flow.

ClearanCes

This  water  heater  is  approved  for  installation  on  combustible 

flooring in an alcove with minimum clearance from combustion 

construction as indicated in Figure 7 and Table 4.
In  all  installations  the  minimum  combustible  clearances  from 

vent piping shall be 6” (15.2 cm). Vent piping passing through a 

combustible wall or ceiling must be a continuous run (no joints) 

and retain 6” (15.2 cm) clearance unless an approved reducing 

thimble is used.
A service clearance of at least 24” (61 cm) should be maintained 

from serviceable parts.

taBle 4. minimum ClearanCes to ComBustiBle or 

non-ComBustiBle ConstruCtion

Model

"A" right Side "b" left Side "C" back "D" Ceiling

Sbl81120Ne 
Sbl81154Ne 
Sbl95180Ne
Sbl95199Ne 

Sbl95250Ne(A) 

0"

0"

0"

12"

0 cm

0 cm

0 cm

30.5 cm

loCating the water heater

Property Damage Hazard

All water heaters eventually leak.

Do not install without adequate drainage.

CAUTION

When  installing  the  heater,  consideration  must  be  given  to 

proper  location.  location  selected  should  be  as  close  to  the 

stack or chimney as practicable, with adequate air supply and as 

centralized with the piping system as possible.

Fire or Explosion Hazard

Read instruction manual before

installing, using or servicing

water heater.

Avoid all ignition sources if you smell gas.

Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

Use only the gas shown on the water heater rating label.

Keep ignition sources away from faucets after extended

periods of non-use.

Maintain required clearances to combustibles.

Do not expose water heater controls to excessive gas

pressure.

There  is  a  risk  in  using  fuel  burning  appliances  such  as  gas 

water heaters in rooms, garages or other areas where gasoline, 

other flammable liquids or engine driven equipment or vehicles 

are stored, operated or repaired. Flammable vapors are heavy 

and  travel  along  the  floor  and  may  be  ignited  by  the  heater's 

igniter  or  main  burner  flames  causing  fire  or  explosion.  Some 

local codes permit operation of gas appliances in such areas if 

they are installed 18" or more above the floor. This may reduce 

the risk if location in such an area cannot be avoided.

Содержание SBL81120NE





















































Отзывы: