State Water Heaters Gas Water Heater Скачать руководство пользователя | Manualshive

Страница: 29 / 51

background image

29

Potential dangers from accidents during installation and use are divided into the following three
categories. Closely observe these warnings, they are critical to your safety.

Prohibited

Disconnect
Power

Ground

Be sure to do

• Failures and damage caused by erroneous work or work not as instructed in this manual are not

covered by the warranty.

• Check that the installation was done properly in accordance with this Installation Manual upon

completion.

• After completion of installation, be sure to hand the Operation Manual (with warranty) to the

customer upon filling in all of the required items.

Requests to Installers

• In order to use the water heater safely, read this installation manual carefully,

and follow the installation instructions.

Caution

WARNING:

If the information in this manual is not followed exactly, a fire or explosion may result

causing property damage, personal injury or death.

Installation must conform with local codes, or in the absence of local codes, the National Fuel Gas
Code, ANSI Z223.1/NFPA 54.

Installation Manual

GAS WATER HEATER

Warning

Caution

Danger

Danger of serious injury or even death as well as danger of fire when the

product is misused by ignoring this symbol.

Possibility of serious injury or even death as well as possibility of fire when

the product is misused by ignoring this symbol.

Possibility of bodily injury or damage to property when the product is

misused by ignoring this symbol.

«
...
27
28
29
30
31
...
»

Содержание Gas Water Heater




















































Отзывы:

Нет отзывов

Похожие инструкции для Gas Water Heater

Бренд: esotec Страницы: 2

Бренд: K&T Страницы: 17

Vickers 25V Series

Бренд: Eaton Страницы: 11

Бренд: TCP Smart Страницы: 16

GHS 1 1/2 GF 32

Бренд: GORMAN-RUPP PUMPS Страницы: 47

Бренд: Waterax Страницы: 6

Бренд: ThermoFlow Страницы: 34

Бренд: Ashley Страницы: 2

Бренд: American Standard Страницы: 12

Бренд: A.O. Smith Страницы: 6

Бренд: Sentiotec Страницы: 28

Бренд: Pearl Страницы: 6

Бренд: Oasis Страницы: 14

Gusher 30 Series

Бренд: Whale Страницы: 8

Бренд: Samoa Страницы: 10

Бренд: Aurora Страницы: 5

Бренд: STIEBEL ELTRON Страницы: 56

Бренд: Grundfos Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды