Star Micronics LS-5 SERIES Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 204

background image

– 94 –

TROUBLESHOOTING

2-12-1. Power is not Supplied

Step

Check

Measure

YES

NO

1

Check parts with different specifications for problems with
usage, defective installation, breakage, and deformation.

•

Main parts to be checked:

(1) LVPS assy, (2) MCU PCB, (3) Feeder assy
(4) Optional feeder unit, (5) HVPS, (6) Fan, (7) Drive assy
(8) Pick up solenoid, (9) Console assy, (10) ROS assy

2

(Check LVPS assy)
Are the voltages as follows?
24VDC between J11-10PIN

↔

J11-2PIN, J11-11PIN

↔

J11-2PIN, J11-12PIN

↔

J11-2PIN

5 VDC between J11-5PIN

↔

J11-2PIN, J11-6PIN

↔

J11-2PIN

•

Disconnect one of the connectors (P/J11) from the MCU

PCB, and after about 5 minutes, turn on the power and check
the voltages.
Check before the output is stopped by the no-load status of the
LVPS assy (within 30 seconds of the power being turned on).

3

Does the fan rotate when the power is turned on?

4

(Check main logic board) *1
Disconnect connector (P/J5) and wait 2-3 minutes. Then turn
on the power and check to see if a display appears on the LCD
and if the fan rotates.

5

(Check HVPS) *2
Disconnect connector (P/J111) from the HVPS. Then turn on
the power and see if a display appears on the LCD and if the fan
rotates.

6

(Check fan) *2
Disconnect connector (P/J18) from the MCU PCB. Then turn
on the power and see if a display appears on the LCD and if the
fuser begins to warm up.

7

(Check drive assy) *2
Disconnect connector (P/J14) from the MCU PCB. Then turn
on the power and see if a display appears on the LCD and if the
fan rotates.

8

(Check pick up solenoid) *2
Disconnect connector (P/J17) from the MCU PCB. Then turn
on the power and see if a display appears on the LCD and if the
fan rotates.

To step 2

To step 3

Replace MCU
PCB.

Check main logic
board.

Replace HVPS.

Replace fan.

Replace drive
assy.

Replace pick up
solenoid.

Replace or
reinstall.

Replace LVPS
assy.

To step 4

To step 5

To step 6
(check all of the
following steps
with the connec-
tor disconnected
from the HVPS)

To step 7

To step 8

To step 9

«
...
96
97
98
99
100
...
»

Содержание LS-5 SERIES













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LS-5 SERIES

Бренд: Oki Страницы: 24

Бренд: VAF instruments Страницы: 24

Бренд: 3DP Страницы: 12

Бренд: QMS Страницы: 2

Бренд: TallyGenicom Страницы: 2

Бренд: Oki Страницы: 2

VersaLink C400V

Бренд: Xerox Страницы: 196

Бренд: Oki Страницы: 189

Бренд: Zebra Страницы: 29

Бренд: Radio Shack Страницы: 42

Бренд: Xerox Страницы: 34

ECOSYS FS-C5350DN

Бренд: Kyocera Страницы: 178

Бренд: MIMAKI Страницы: 20

Бренд: RAYSHAPE Страницы: 41

Бренд: ZKTeco Страницы: 38

Бренд: Canon Страницы: 88

Бренд: Canon Страницы: 56

Бренд: Canon Страницы: 364

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды