Star Micronics LS-5 SERIES Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 204

background image

– 107 –

TROUBLESHOOTING

3-13. Faulty Paper Size Switch

Step

Check

Measure

YES

NO

1

Check parts with different specifications for problems with
usage, defective installation, breakage, deformation, and adhe-
sion of grime or foreign matter.

•

Main parts to be checked:

(1) Feeder assy, (2) Optional feeder unit, (3) Feeder PCB
(4) Feeder PCB aux, (5) Size spring, (6) MCU PCB
(7) Harness assy 1tray, (8) Harness assy out, (9) LVPS assy

2

(Check size spring) *1
When the size spring is pressed, does the paper size switch in
the position corresponding to the size spring go on?
Remove Tray 1/Tray 2 and check visually.

3

(Check power supply of paper size switch) *1 *2
Is 5 VDC being supplied between P/J13-2PIN

↔

P/J13-4PIN?

4

(Check paper size signal) *1 *2 *3
Is normal voltage being supplied between P/J13-5PIN {P/J13-
6PIN}

↔

P/J13-4PIN when the four paper size switches are in

the correct ON/OFF combination?

5

(Check harness assy 1tray) *1
Is there conductivity between J13

↔

J115 on the harness assy

Tray 1?

6

Are the paper size switches of Tray 1 defective?

7

(Check feeder PCB)
Is there conductivity between P115

↔

P116 of the feeder

PCB?

8

(Check harness assy out)
Is there conductivity between P116

↔

J115 of the harness assy

out?

*1: This is noted for both Tray 1 (upper cassette feeder) and Tray 2 (lower cassette feeder). To distinguish Tray 1 from

Tray 2, items concerning Tray 2 are enclosed in brackets { }.

*2: Check with the connector (P/J111) disconnected from the HVPS.
*3: For information on the correct voltage to be supplied between P/J13-5PIN {P/J13-6PIN}

↔

P/J13-4PIN in response

to the ON/OFF combinations of the paper size switches, please refer to Chapter 4, Section 5-2, “Connection Wiring
Diagram Between Parts”.

Replace or
reinstall.

Replace the size
springs of the
pertinent tray.

To section 3-1

To step 5

Replace harness
assy 1tray.

To step 7

Replace feeder
PCB.

Replace harness
assy out.

To step 2

To step 3

To step 4

Replace MCU
PCB.

To step 6

Replace feeder
PCB.

To step 8

Replace feeder
PCB aux.

«
...
109
110
111
112
113
...
»

Содержание LS-5 SERIES













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LS-5 SERIES

Бренд: EBS Страницы: 4

Бренд: NCR Страницы: 38

Бренд: BadgePass Страницы: 2

Document WorkCentre 480cx

Бренд: Xerox Страницы: 318

Бренд: Xerox Страницы: 76

Бренд: Xerox Страницы: 11

Бренд: Xerox Страницы: 352

Color 560 Printer

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 105

Бренд: Xerox Страницы: 42

Бренд: Xerox Страницы: 13

Бренд: Xerox Страницы: 132

CopyCentre C2128

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 20

Бренд: Xerox Страницы: 34

Бренд: Xerox Страницы: 8

Бренд: Xerox Страницы: 70

Бренд: Xerox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды