Star Micronics IFBD-BE07 Скачать руководство пользователя страница 45

Страница: 45 / 89

IFBD-HE0708 BE07 User’s Manual

3-36

3.2 Other Specifications

3.2.1. Operating Time

There are approximately 14 seconds from the time the power is turned on to the startup of the TCP/IP (start of IP address

acquisition).

It takes approximately 18 seconds before the TCP/IP services (HTTP, TELNET, FTP, LPD, Raw Socket Print) can be used after

turning on the power.

Note: When acquiring the IP address by Dynamice (DHCP/BOOTP, RARP), this time may

lengthen depending on the server response time.

3.2.2. Push Switch

While the TCP/IP is operating (the power has been turned on, and it is within the elapse time described in section 3.2.1 Startup

Time), if the push switch is continued to be held down, the LED display pattern will change according to the times shown below.

When the switch is released, the product will enter each special mode.

Special Mode

Phase

SW Pressing Time

LAN Connector

LED Blinking Pattern

Special Mode

Green

Red

1 second to less than 5 seconds

Blinking

NIC setting initialize mode (*2)

5 second to less than 9 seconds

Extinguished

Blinking

Reserved (Undefined)

9 second to less than 13 seconds

Blinking

Extinguished

Reserved (Undefined)

Over 13 seconds (*1)

Note 1. When Phase 3 is exceeded, press the switch for 1 second to return to Phase 1.

Note 2. Execution procedures for the NIC setting initialize mode

1. After entering this mode, press the push switch once and release it.

The LED display will be “Green = Extinguished; Red = Extinguished” and the initializing of the NIC settings in the

non-volatile memory will begin.

2. If the initialization is successful, the printer will automatically be reset.

Do not turn off the power or apply a reset until this reset has been applied.

Also, if the NIC setting initialization fails, the LED display will be “Green = Extinguished; Red = Lit” and all opera-

tions will stop.

If so, turn the power off.

Note: When turning the power on, a different mode (automatic firmware update function using

TFTP client) will startup that is different to the above functions, for the operations when

turning the power on with the push switch pressed. For details, see section 3.1.8 TFTP Cli-

ent.

Содержание IFBD-BE07


























































































Результаты поиска

Содержание IFBD-BE07

Отзывы:

Похожие инструкции для IFBD-BE07

Бренды по названию

Популярные бренды

Star Micronics IFBD-BE07, Руководство пользователя

Результаты поиска

Содержание IFBD-BE07

Отзывы:

Похожие инструкции для IFBD-BE07

Бренды по названию

Популярные бренды