10
ENGLISH
Operation (Fig. 5)
Instructions
WARNING:
Always observe the safety
instructions and applicable regulations.
WARNING: To minimize the danger
of serious personal injury, please
switch off the tool power and
disconnect all plugs before adjusting
or removing/installing any accessory.
Before reassembling the tool, press and
release the trigger switch to make sure
the tool is already switched off.
WARNING:
• Make sure all materials to be grinded
are secured in position.
• Apply slight pressure to the tool. Do
not apply side pressure to the abrasive
disc.
• Avoid overloading. If the tool becomes
hot, let it spin for a few minutes with
no load.
1. Be sure to hold the tool tightly with both hands
(one hand on housing, the other on side
handle). Start the tool and bring the grinding
wheel on the workpiece.
2. Keep the edge of the wheel tilted at angle from
15 to 30 degrees against the surface of the
workpiece.
3. When using a new grinding wheel, do not
operate the wheel in the B direction, otherwise,
it will cut into the workpiece. When the edge
of wheel has been rounded off, you are free to
operate the grinder in either the A or B direction.
Starting and Stopping (Fig. 1)
WARNING:
Before using the tool, check
whether the handle is tightened securely.
Check whether the ON/OFF switch is
working normally.
Before plugging in the tool to the power supply,
check whether the switch is in the OFF (o) position
when pressing the rear end of the switch.
Slider switch (STGS6100/7100)
Before plugging in the tool to the power supply,
check whether the switch is in the OFF (a) position
when pressing the rear end of the switch.
To start the tool, press the rear end of the switch
and slide it forward. Then press the front end of the
switch to lock it. Press the rear end of the switch to
stop the tool.
Toggle swithch (STGT6100/7100)
To run the tool, press the switch (j) in before moving it
completely forward.
To stop the tool, move the switch (j) back the
opposite way.
to stop the tool in continuous operation, press on
back part of the switch.
WARNING:
Do not switch the
tool on or off while under load
conditions.
WARNING:
Do not switch the tool on or
off while under load conditions.
Switches
CAUTION:
Hold the body of the tool
firmly to maintain control of the tool at start
up and during use and until the wheel or
accessory stops rotating. Make sure the
wheel has come to a complete stop be
fore laying the tool down.
NOTE:
To reduce unexpected tool movement, do not
switch the tool on or off while under load conditions.
Allow the grinder to run up to full speed before
touching the work surface. Lift the tool from the surface
before turning the tool off. Allow the tool to stop
rotating before putting it down.
SLIDER SWITCH (STGS7100/STGS6100)
WARNING:
Before connecting the tool to
a power supply, be sure the slider switch
is in the off position by pressing the rear
part of the switch and releasing. Ensure
the slider switch is in the off position as
described above after any interruption
in power supply to the tool, such as the
activation of a ground fault interrupter,
throwing of a circuit breaker, accidental
unplugging, or power failure. If the slider
switch is locked on when the power is
connected, the tool will start unexpectedly.
To start the tool, slide the slider switch (a) toward the
front of the tool.
To stop the tool, release the slider switch.For
continuous operation, slide the switch toward the
front of the tool and press the forward part of the
switch inward.
To stop the tool while operating in continuous mode,
press the rear part of the slider switch and release.
Содержание STGS7100
Страница 1: ...STGS7100 STGT7100 English Original Instruction 5 简体中文 13 ...
Страница 2: ...Figure 1 b c c d h f g e i k Figure 2 Figure 3 n a ...
Страница 3: ...Figure 5 Figure 6 Figure 4 h f d e 15o 30o A B ...
Страница 4: ...Figure 7 j ...