background image

 3

3

GENERAL SAFETY RULES

ATTENTION:

 

When using gasoline motors like this 

one, basic safety rules must be observed in order 

to reduce risk of accidents and/or damage to the 

machine. Read all instructions again before using 

the device in the future.

SAFETY PRECAUTIONS

• Read these instructions carefully.

• Never allow children or persons who are not 

familiar with these instructions to operate the 

machine. Local regulations may impose a limit on 

the age of the operator.

• Never operate the machine around children or 

pets.

• Keep in mind that the operator of the machine is 

responsible for any accidents that may occur to 

third parties and/or to their property.

• The machine must be operated solely by a 

capable person who is qualified to operate it.

• Always wear appropriate footwear (safety shoes) 

and long pants when operating this tool.

• Do not operate the machine when barefoot or 

when wearing open sandals.

• Carefully inspect the area where the equipment 

will be operated and remove any objects that could 

be thrown by the machine.

CAUTION

-

 Gasoline is extremely flammable:

- Store fuel only in containers designed for this 

purpose.

- Refill the machine with fuel only when outdoors 

and never smoke when re-filling the equipment 

with fuel.

- Add fuel before starting up the motor. Never 

remove the fuel tank plug or add gasoline while the 

motor is running or when the engine is hot.

- If gasoline is spilled, do not attempt to start up the 

motor; take the machine away from the area where 

the gasoline was spilled and keep all sparks away 

until the gasoline has evaporated.

• Replacing a defective muffler.

• Before each use, always check to be sure that 

the tools are not worn out or damaged.  When 

changing a worn-out or damaged component or 

bolt, change all similar components out in order to 

preserve balance.

• Do not operate the machine in a confined space 

where dangerous carbon monoxide vapors could 

accumulate.

• Always be sure that the machine is balanced on 

its stands.

• Walk, never run, with the machine.

• Work is a diagonal direction, never from up and 

down.

• Pay very close attention when changing direction 

on slopes.

• Never work on slopes that are too steep.

• Pay very close attention when reversing the 

machine or pulling it towards you.

• Do not change direction adjustments and do not 

exceed the speed limit of the motor.

• When starting the motor, following the 

instructions carefully and keep your feet far away 

from the blades.

• Do not put your hands or feet near or on rotating 

parts.

• Never pick up or carry the machine while the 

motor is running .

• Shut off the motor:

• Every time you leave the machine. 

- Before refilling it with gasoline.

- When performing maintenance and cleaning 

operations.

- While changing tools.

- When using any traction force other than the 

engine to move the machine.

• Reduce the starter when shutting off the machine 

and close the fuel hose when finished working.

• Use the tiller only with the blades provided.

• Always place your hands on the handlebar when 

using the machine. Do not hold the machine by its 

other parts while operating it.

• Keep all nuts, bolts and screws properly tightened 

so that you are sure that equipment is in optimum 

safety condition.

• Never store the equipment with gas in the tank, 

inside a building where vapors could reach an 

open flame or a spark.

G
B

Содержание SGT-25-450-H





















Отзывы: