Stanley FATMAX SFMCMW2651, Оригинальное руководство пользователя

Страница: 46 / 192

44
ENGLISh
Blade Sharpening
KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE. A DULL
BLADE DOES NOT CUT GRASS CLEANLY.
WARNING:
Use gloves and proper eye protection while
removing, sharpening, and installing blade. Ensure that
safety key and battery pack are removed.
Sharpening the blade twice during a mowing season is usually
sufficient under normal circumstances. Sand causes the blade
to dull quickly. If your lawn has sandy soil, more frequent
sharpening may be required.
REPLACE BENT OR DAMAGED
BLADE IMMEDIATELY.
When Sharpening the Blade:
• Make sure blade remains balanced.
• Sharpen blade at the original cutting angle.
• Sharpen cutting edges on both ends of blade, removing
equal amounts of material from both ends.
To Sharpen Blade in a Vise (Fig. M)
1. Be sure the bail handle is released, the blade has stopped
and safety key and battery packs are removed before
removing the blade.
2. Remove blade from mower. See instructions for Removing
and Installing Blade
.
3. Secure blade 29 in a vise 32 .
4. Wear proper eye protection and gloves and be careful not
to cut yourself.
1. Cut a piece of 2" x 4" wood 25 (about 2 feet long) (610 mm)
to keep blade from turning when removing the flange
nut
27 .
WARNING:
Use gloves and proper eye protection. Turn the
mower on its side. Be careful of sharp edges of blade.
2. Position wood and unscrew flange nut counterclockwise
with a 18 mm wrench 26 as shown in Fig. L.
3. Remove square metal blade spacer 30 , square plastic
blade insulator 28 and blade 29 as shown in Fig. L. The
blade fan 31 should not be removed. Examine all pieces for
damage and replace if necessary.
4. Install sharpened or new blade on shoulder of the blade fan
as shown in Fig. L
NOTE: When replacing sharpened or new blade on shoulder of
blade fan, make sure the “GRASS SIDE” on the blade will be
facing the ground when the mower is returned to its normal
upright position.
5. Install the plastic blade insulator 28 on the blade such that
the raised lips on one side engage the edges of the blade.
6. Install the blade spacer 30 so that it sits inside the raised
lips on the other side of the blade insulator. Be sure to align
the flats in the hole of the blade spacer with the flats of
the shaft, rotating the blade and blade insulator together
as necessary.
7. Position piece of wood to keep blade from turning as shown
in Fig. L. Install flange nut 27 with the flange against the
blade spacer 30 and securely tighten the blade 29 with a
18 mm wrench 26 .
Protecting the Environment
w
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that
can be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com .
Optional Accessories
WARNING: Since accessories, other than those offered
by STANLEY FATMAX, have not been tested with this
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only STANLEY
FATMAX recommended accessories should be used with
this product.
Consult your dealer for further information on the
appropriate accessories.
Release bail handle 6 to turn mower off, let the blade come
to a stop and then remove the battery packs and safety key.
Clean out any clippings which may have accumulated on the
underside of the deck. Do not spray water or other liquids. After
several uses, check all exposed fasteners for tightness.
D
Cleaning
WARNING:
Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING:
Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
C
Lubrication
Your power tool requires no additional lubrication.
Blade Balancing (Fig. N)
Check balance of the blade 29 by placing center hole in the
blade over a nail or round screwdriver 33 , clamped horizontally
in a vise 32 . If either end of the blade rotates downward, file
along the sharp edge of that dropping end. Blade is properly
balanced when neither end drops.
5. Carefully file the cutting edges of the blade with a fine tooth
file 34 (not included) or sharpening stone (not included),
maintaining the angle of the original cutting edge.
6. Check balance of blade. See instructions for
Blade Balancing
.
7. Replace blade on mower and tighten securely.