Stanley Fatmax SFMCG700, Оригинальное руководство пользователя

Страница: 13 / 152

13
ENGLISH (Original instructions)
Cleaning and disposal
u
All surfaces in the work area should be vacuumed and
thoroughly cleaned daily for the duration of the wire
brushing project. Vacuum filter bags should be changed
frequently.
u
Plastic drop cloths should be gatheredup and disposed
of along with any dust chips or other removal debris.
They should be placed in sealed refuse receptacles and
disposed of through regular trash pick-up procedures.
During clean up, children and pregnant women should be
kept away from the immediate work area.
u
All toys, washable furniture and utensils used by children
should be washed thoroughly before being used again.
Using cutting wheels
Do not use edge grinding/cutting wheels for surface grinding
applications because these wheels are not designed for side
pressures encountered with surface grinding. Wheel breakage
and injury may result.
u
Allow tool to reach full speed before touching tool to work
surface.
u
Apply minimum pressure to work surface, allowing tool to
operate at high speed. Cutting rate is greatest when the
tool operates at high speed.
u
Once a cut is begun and a notch is established in the
workpiece, do not change the angle of the cut. Changing
the angle will cause the wheel to bend and may cause
wheel breakage.
u
Remove the tool from work surface before turning tool off.
Allow the tool to stop rotating before setting it down.
Maintenance
Your STANLEY FATMAX tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u
Or run the battery down completely if it is integral and then
switch off.
u
Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u
Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
u
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u
Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
Accessories
Warning! Since accessories, other than those offered by
STANLEY FATMAX, have not been tested with this product,
use of such accessories with this tool could be hazardous. To
reduce the risk of injury, only STANLEY FATMAX
recommended accessories should be used with this product.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com.
Technical data
SFMCG700 (H1)
Voltage
V
DC
18
Rated speed
Min
-1
8,000
Disc diameter mm 125
Disc bore mm 22
Max disc thickness
grinding disc mm 6
cutting disc mm 3.5
Spindle diameter M14
Spindle length (with the
inner flange fitted)
mm 12.8
Spindle length (without the
inner flange fitted)
mm 18.6
Weight kg 1.85 (without battery)
Charger SFMCB11 SFMCB12 SFMCB14
Input Voltage
V
AC
230 230 230
Output Voltage
V
DC
18 18 18
Current A 1.25 2 4
Battery
SFMCB201 SFMCB202 SFMCB204 SFMCB206
Voltage V
DC
18 18 18 18
Capacity Ah
1.5 2.0 4.0 6.0