Stanley FATMAX FMES550, Оригинальное руководство пользователя

Страница: 8 / 28

English
8
(original instructions)
Sawing metal
@
Warning! Do not use a vacuum when cutting
metal. Metal filings will be hot and may
cause fire. Be aware that sawing metal takes
much more time than sawing wood.
u
Use a saw blade suitable for sawing metal.
u
When cutting thin sheet metal, clamp a piece of scrap
wood to the back surface of the workpiece and cut
through this sandwich. Blade motion and is designed for
cutting soft materials such as wood or plastic. It provides a
faster cut, but with a less smooth cut across the material.
Your jig saw has a Pendulum Stroke dial. Use of this dial
is explained in the next section.
u
Warning: Never use pendulum action to cut metal.
u
Spread a film of oil along the intended line of cut.
Rip fence (optional)
u
Ripping and circle cutting without a pencil line are easily
done with a rip fence and circle guide.
Attaching rip fence (Fig. H )
u
Insert rip fence (16) into the shoe plate slots with the cross
bar facing down as shown in figure I.
u
Place screw (17) into hole in bottom of shoe plate.
u
Align clamp bar (18) over screw with lipped edge facing
down and pointing towards the rear of the saw.
u
Using a phillips screwdriver, run the screw into the
threaded hole in the bar clamp as shown in figure G.
u
Adjust to width of cut and tighten screw.
Circle cutting (Fig. I)
u
Insert rip fence into slot on the right side of shoe plate with
cross bar facing up.
u
Adjust rip fence so that distance from blade to hole in
cross bar is the desired radius and tighten screw.
u
Place saw so that centre of hole in cross bar is over
centre of circle to be cut (make plunge cut, drill hole for
blade or cut inward from edge of material to get blade
into position).
u
When saw is properly positioned, drive a small nail
through hole in cross bar into exact centre of circle to
be cut.
u
Using rip fence as a pivot arm, begin cutting circle.
Maintenance
Your Stanley FatMax tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
@
Warning! Before performing any maintenance on
the tool, remove the battery from the tool. Unplug
the charger before cleaning it.
u
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com
Notes
Stanley FatMax’s policy is one of continuous improvement
to our products and as such, we reserve the right to change
product specifications without prior notice.
Standard equipment and accessories may vary by country.
Product specifications may differ by country.
Complete product range may not be available in all countries.
Contact your local Stanley FatMax dealers for range
availability.
Service information
Stanley FatMax offers a full network of company-owned
and/ or authorized service agents throughout your country.
All Stanley FatMax Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
power tool service. Whether you need technical advice, repair,
or genuine factory replacement parts, contact the Stanley
FatMax location nearest to you.
Technical data
Jigsaw FMES550
Voltage
V
ac
220~240
Frequency Hz 50/60
Power input W 550
Rated speed
min
-1
500 - 3000
Bevel Cutting º +/-45
Max depth of cut
Wood/ Steel/ Aluminium
mm 75/6/10
Stroke Length mm 19
Pendulum Action Yes
Weight kg 1.9
Two years warranty
If your Stanley FatMax product becomes defective due to faulty materials or
workmanship within 24 months from the date of purchase, Stanley FatMax
guarantees to replace all defective parts free of charge or – at our discretion –
replace the unit free of charge provided that:
u
The product has not been misused and has been used in accordance with the
instruction manual;
u
The product has been subject to fair wear and tear;