INSTALLATION & OPERATING INSTRUCTIONS
GENERAL
When installing, operating and maintaining your
Stanley Stove, respect basic standards of fire safety.
Read these instructions carefully before commenc-
ing the installation. Failure to do so may result in
damage to persons and property. Consult your local
Municipal office and your insurance representative
to determine what regulations are in force. Save
these instructions for future reference. Please note
that it is a legal requirement under the Building
Regulations that the installation of the stove is either
carried out by a RGI Registered Installer (ROI) or a
Gas Safe Installer (NI or UK) or equivalent.
It is important to note that once a type of gas has
been specified the stove cannot be run off any
other type of gas (i.e. Natural Gas or L.P.G.).
The burner units are not interchangeable
between Natural Gas & L.P.G.
Special care must be taken when installing the stove
such that the requirements of the Health & Safety at
Work Act are met.
Handling
Adequate facilities must be available for loading,
unloading and site handling.
Asbestos
This stove contains no asbestos. If there is a possi-
bility of disturbing any asbestos in the course of
installation then please seek specialist guidance and
use appropriate protective equipment.
Metal Parts
When installing or servicing this stove care should
be taken to avoid the possibility of personal injury.
“IMPORTANT WARNING”
This stove must not be installed into a chimney sys-
tem that serves any other heating appliance.
7
The complete installation must be done in accor-
dance with current Standards and Local Codes. It
should be noted that the requirements and these
publications may be superseded during the life of
this manual.
Northern Ireland & UK Installation
Install in accordance with the following:
* The Gas Safety Regulations 1998 (as amended).
* B.S. 5440: Parts 1 & 2, Installation & Maintenance
of Flues and Ventilation for Gas Appliances of rated
input not exceeding 70kW
* B.S. 5871: Parts 1, 2 & 3, Specification for
Installation of Gas Fires, Convector Heaters,
Fire/Back Boilers and Decorative Fuel Effect Gas
Appliances.
* Building Regulations for England, Scotland, Wales
& Northern Ireland.
Your Stanley Gas stove is supplied with the following
items:
•
Ceramic Log Set
•
Remote Control
•
Flue Restrictor Plates
ELECTRICAL SUPPLY
All wiring external to the appliance must conform to
the current BS 7671 (UK) BS 7462 Safety Document
635: ETC Part 1, Section 5.4.6 and The Electricity at
Work Regulations.
If connecting the optional Wi-Fi module (for remote
smart phone control), the unit requires a 220V-240V
50L/2 supply connection and any system controls to
the mains supply must be through a fused double
pole switch having contact separation of at least
3mm with a fuse rated at 3 amp and located in a
readily accessible position close to the appliance.
Connection should be made through the cable sup-
plied only.
LOCATION
There are several conditions to be considered in
selecting a location for your Stanley Stove.
a.
Position in the area to be heated, central
locations are usually best.
b.
Allowances for proper clearances to
combustibles.
c.
Proposed Routing of Flueing System.
d.
Allowances for proper clearances for
maintenance work.
Republic of Ireland Installation
Install in accordance with the following:
* Building Regulations Part J
* I.S. 813 - Domestic Gas Installations
* I.S. 265 - Part 1 & 2 - Installation of Gas Service
Pipes
* I.S. 327 1990 - Domestic Installation using
Liquidified Petroleum Gases.
CLEARANCES TO COMBUSTIBLES
Maintain at least the following clearances to all
combustible material - refer to Fig 1:
Clearance to
Combustibles (mm)
Clearance to Non
Combustibles(mm)
Rear (R)
75
50
Side (S)
500
50
Top (T)
300
50
Front (F)
1000
75
Содержание Argon F500 OVAL
Страница 23: ...WIRING DIAGRAM 23 ...
