Standard Horizon HX751 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 56

background image

Page 23

HX751

6. When a signal is received, adjust the volume (Press the

[

VOL

] key, followed by the [

]/[

] key) to desired listen-

ing level. The

TX/BUSY

indicator illuminates green indi-

cating that the channel is being used.

NOTE

You may change the speaker audio to have a high or lower sounding
pitch to assist listening in quiet or noisy environments. See Menu item
“

02 PC

(

AUDIO PITCH CONTROL

)” (page 36) for details.

6.4 TRANSMISSION

1. Perform the “

6.3 RECEPTION

” discussion above.

2. Before transmitting, monitor the channel and make sure it is clear.

THIS IS AN FCC REQUIREMENT!

3. For communications over short distances, press the

[

H/L

(

)] key until “

” is displayed on the LCD. This

indicates Low power (approximately 1 watt).

Note

: Transmitting on 1 watt prolongs battery life. Low

power (1 watt) should be selected whenever possible.

4. If using Low power is not effective, select Medium power

(2.5 watts: “

” icon appears), High power (5 watts: “

”

icon appears), or Normal power (6 watts: No icon) by
pressing the [

H/L

(

)] key.

5. When receiving a signal, wait until the incoming signal stops before trans-

mitting. The transceiver cannot transmit and receive simultaneously.

6. Press the

PTT

(Push-To-Talk) switch to transmit. During

transmission, the “

” indicator will appear on the dis-

play and the

TX/BUSY

indicator will grow red.

7. Position your mouth about 1/2 to 1 inch (1.2 ~ 2.5 cm)

away from the small mic hole. Speak slowly and clearly into the micro-
phone.

8. When the transmission is finished, release the

PTT

switch.

6.4.1 TRANSMIT TIME - OUT TIMER

(

TOT

)

While the

PTT

switch is held down, transmission time is limited to 5 minutes.

This prevents prolonged (unintentional) transmissions. About 10 seconds be-
fore automatic transmitter shutdown, a warning beep sounds from the speaker.
The transceiver automatically switches to the receiving mode, even if the

PTT

switch is held down. Before transmitting again, the

PTT

switch must first be

released, then wait 10 seconds and then pressed again. This Time-Out-Timer
(TOT) prevents a continuous transmission that would result from an acciden-
tally stuck

PTT

switch.

«
...
21
22
23
24
25
...
»

Содержание HX751

























































Отзывы:

Нет отзывов

Похожие инструкции для HX751

Бренд: Nautel Страницы: 205

Бренд: Nautel Страницы: 70

Бренд: Nautel Страницы: 72

Бренд: Nautel Страницы: 166

Бренд: NAD Страницы: 5

Бренд: NAD Страницы: 24

Бренд: NAD Страницы: 65

Бренд: AOR Страницы: 95

Multimedia Master Remote

Бренд: Remotec Страницы: 19

Бренд: Bang & Olufsen Страницы: 14

Бренд: Spektrum Страницы: 16

Бренд: Zamel Страницы: 2

Бренд: Strong Страницы: 35

ES200-7CD - REV B

Бренд: Simrad Страницы: 28

Бренд: Avermedia Страницы: 2

HP450 2A Rugged

Бренд: Alan Страницы: 174

Бренд: Me Страницы: 50

Бренд: TYT Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды