background image

POWER OFF:

Pedal movement or press any button.
Automatic shut off after 4 minutes of
inactivity. Resets all values to zero.

POWER  ON:

USING THE METER

FUNCTIONS:

SCAN:

TIME:

SPEED:

DISTANCE:

CALORIES:

PULSE:

Upper display automatically scans 

SPEED, TIME, DISTANCE, CALORIES, PULSE,

 and

TEMPERATURE

 in sequence with a change every four seconds.  Press and release the 

MODE

 button

until 

"SCAN" 

appears on display.

Displays the current speed, from zero to 999 Mile/Hr.
Counts upward to 99:59 in one second increments. Counts down from preset value.
Displays distance up to 99.99 miles in increments of 0.01 miles. Counts down from preset value.
Displays the calories consumption, from zero to 9999 cal. Counts down from preset value.
The calories readout is an estimate for an average user. It should be used only as a comparison
between workouts on this unit.
Displays your pulse rate in beats per minute.  To display pulse, grasp the Pulse Sensors on the 

Stationary

Handlebar

, one in each hand. The heart symbol " 

 " will begin flashing when the Electronic Meter

senses your pulse.  Your pulse will be displayed approximately five (5) seconds after the heart icon is
displayed.  If you do not place your hands correctly and 60 seconds passes without a pulse input, the
Meter will turn off the pulse circuit.  Press the 

MODE

 button

 

to restart and place your hands back on the

Pulse Sensors correctly, the pulse readout will appear again.
If you preset the PULSE value, the Meter will warn you with an audible alarm when your pulse exceeds
the set value. Stop exercising until your pulse comes down.

FUNCTION BUTTONS:

RESET :

This button will reset each function to zero.
To reset all functions to zero, press the button
and hold it down for three seconds.

SET :

Press to set target values for TIME, DISTANCE,
CALORIES, and PULSE.

MODE :

Press and release to select each function for
display on Upper Display or preset target values.
Press the button and hold it down for three
seconds to reset all functions to zero.

Open the Battery Door on the back of the meter.
The meter operates with two AA batteries, two batteries included.  Refer
to the illustration to install or replace the batteries.

1.
2.

HOW TO INSTALL AND REPLACE BATTERIES:

Do not mix a new battery with an old battery.
Use the same type of battery.  Do not mix an alkaline battery with another
type of battery.
Rechargeable batteries are not recommended.

1.
2.

3.

NOTE:

Lower

Display

Upper

Display

TEMPERATURE:  

Displays the current environment temperature.

PRESET VALUES OPERATION:

Stop pedaling for four seconds.  Press the 

MODE

 button to select functions for preset target values. The meter will

cycle through the functions as follows and allow you to set the function values.

Time (0:00 to 99:00)

 Distance (0.0 to 99.5 mile)

 Calories (0 to 9999 cal)

 Pulse (30 to 240 BPM)

Use 

SET

 & 

RESET

 buttons to enter desired values and press 

MODE

 button to confirm and move to next function for

presetting. Or, just press the 

MODE

 button to pass the setting of some functions.  Start to run the Meter functions by

pedaling.

11

AA Batteries

Содержание 55-1771























Отзывы: