08
17. SHUTTER RELEASE (FOR CASSETTE AWNINGS ONLY)
This is a specific function available only in the CASSETTE AWNING installation mode. The factory sets this function as “inactive”. If the
function is activated, when the cassette closes a very brief downward movement is commanded so as to reduce the traction on the
shutter with closed cassette. The duration of the movement can be set (see Table 01 - Shutter Release) following the procedure below.
No. of movements
Threshold
1
2
3
4
5
Function not active
10 msec
20 msec
30 msec
40 msec
Tab. 01 - Shutter Release
17.1 USING REMOTE CONTROL Item 596
01. Bring the motor to the intermediate position.
02. Briefly press
MENU
on the back. The motor performs an up/down movement.
03. Display shows: - - . Press
DOWN 6 times
. 06 appears on the display.
04. Press
STOP
. The motor performs an up/down movement.
05. Press
UP
. The motor shows the current value (from 1 to 5 movements).
06. Press
UP
as many times as the setting you want (from 1 to 5).
07. Press
STOP
. The motor shows the new setting (from 1 to 5 movements).
08. Press
MENU
to exit.
01. Bring the motor to the intermediate position.
02. Turn off the power, wait a few seconds, then power up again.
03. Within 15 seconds, briefly and quickly press
UP 3 times
and
DOWN 3 times
*.
The motor performs an up/down movement.
04. Within 15 seconds, briefly and quickly press
DOWN 6 times
.
After 2 seconds, the motor signals the current value (from 1 to 5 movements).
05. Briefly press
UP
the number of times equal to the desired setting (from 1 to 5). After
2 seconds, the motor signals the new setting (from 1 to 5 movements).
06. Wait for 5 seconds. The motor exits the menu without any movement.
17.3 USING COMMAND BUTTONS
Wait for 5
seconds
12
3
9
6
6 x DOWN
ON
3 x UP
3 x DOWN
press UP
from 1 to 5
times
01. Bring the motor to the intermediate position.
02. Press 3 times on
PROG
*. The motor performs an up/down movement.
03. Press
6 times on DOWN
. The motor performs an up/down movement.
04. Press
STOP
. The motor shows the current value (from 1 to 5 movements).
05. Press
UP
as many times as the setting you want (from 1 to 5).
06. Press
STOP
. The motor shows the new setting (from 1 to 5 movements).
07. Press
PROG
3 times
to exit.
17.2 USING REMOTE CONTROL Item 595
(*) The buttons must be pressed shortly, max 1 second between two pressures.
18. ORIENTATION (MICRO MOVEMENTS)
01. Bring the motor to the intermediate position.
02. Turn off the power, wait a few seconds, then power up again.
03. Within 15 seconds, briefly and quickly press
UP 3 times
and
DOWN 3 times
*.
The motor moves up/down.
04. Within 15 seconds, briefly and quickly press
DOWN 7 times
.
The motor shows the current value (from 1 to 5 movements).
05. Briefly press
UP
as many times as the setting you want (from 1 to 5).
06. After 5 seconds, the motor signals the new setting (from 1 to 5 movements).
To adjust:
01. Briefly press a button, then immediately press and hold it
18.3 USING COMMAND BUTTONS
Allows you moving the motor in short strokes. Useful function for situations in which the rolling shutter consists of adjustable slats.
The function is already active, but can be deactivated and customised.
If the function is active, you can use both the wall-mounted buttons and the remote control to move the motor in strokes:
- with the wall-mounted buttons (only with pulse logic), briefly press a button, then immediately press the same button again, keeping it
pressed.
- with remote control Item 596, keep pressed the two special buttons with curved arrows (if necessary, refer to the manual of the
remote control supplied).
- with remote control Item 595, briefly press STOP twice, then immediately afterwards hold down the UP or DOWN button (if
necessary, refer to the manual of the remote control supplied).
It is possible to adjust the duration of the strokes (see Table 02 - Orientation Time). To modify this parameter, follow the instructions
provided below.
10.1 UTILIZZANDO IL TRASMETTITORE (solo Atom e Leg)
01. Bring the motor to the intermediate position.
02. Briefly press
MENU
. The motor moves up/down. Display shows: - - .
03. Press
7 times on DOWN
. 07 appears on the display.
04. Press
STOP
. The motor shows: up/down.
05. Press
UP
. The motor shows the current value (from 1 to 5 movements).
06. Press the
UP
button a number of times equal to the desired setting (from 1 to 5)
07. After 5 seconds, the motor signals the new setting (from 1 to 5 movements).
08. Press
MENU
to exit
To adjust:
01. Press the ORIENTATION button on the remote control.
No. of movements
Threshold
1
2
3
4
5
Function not active
50 msec
100 msec
150 msec
200 msec
Tab. 02 - Orientation Time
Advanced Info
18.2 USING REMOTE CONTROL Item 595
10.1 UTILIZZANDO IL TRASMETTITORE (solo Atom e Leg)
01. Bring the motor to the intermediate position.
02. Press
3 times on PROG
*. The motor shows: up/down.
03. Press
7 times on DOWN
.
04. Press
STOP
. The motor shows: up/down.
05. Press
UP
. The motor shows the current value (from 1 to 5 movements).
06. Press
UP
as many times as the setting you want (from 1 to 5).
07. After 5 seconds, the motor signals the new setting (from 1 to 5 movements).
08. Press
PROG 3 times
to exit.
To adjust:
01. Briefly press
twice on STOP
, and then hold down UP or DOWN.
18.1 USING REMOTE CONTROL Item 596
UP
Wait for 5
seconds
12
3
9
6
7 x DOWN
ON
3 x UP
3 x DOWN
press UP
from 1 to 5
times
UP
(*) The buttons must be pressed shortly, max 1 second between two pressures.
