background image

LAX 600 series

3

en

1. Intended use

Congratulations on the purchase of your STABILA measuring tool. 

STABILA laser units from the LAX 600 series are simple to operate laser lines with three 

360° laser lines for levelling in a horizontal and vertical direction, for transferring/creating 

90° angles and for plumb lines. 

The laser units have a sealed casing (IP 65) for use on building sites. 

They are self-levelling within a range of ±4°. 

The laser lines are pulsed, which makes it possible to work over greater distances using 

a special STABILA line receiver. For more information refer to the operating instructions 

for the line receiver.

The LAX 600 series can only be operated with a 12 V Li-Ion CAS System battery. 

LAX 600 G:

 

Receivers must be suitable for green laser beams.

These operating instructions are valid for all devices from the LAX 600 series.  

The laser beams are only displayed in one colour.

If you still have questions after reading the operating instructions,  

you can obtain advice over the phone at any time: 

+49 / 63 46 / 3 09 - 0

Equipment and functions:

•  Pulsed laser lines
•  1x 360° horizontal laser line 
•  2x 360° vertical laser lines
•  90° angle in horizontal and vertical direction
•  Plumb line laser function
•  Manual mode
•  1/4" tripod socket
•  Carrying case
•  STABILA CAS – 12 V Li-Power 2.0 Ah battery – not included in every set
•  SC 30 charger, 12-18 V, CAS system – not included in every set

LAX 600 G:

 

•  Includes green laser beams to improve visibility with the naked eye.

2.2 Safety instructions for the Li-ion battery pack

Thoroughly read the safety instructions and operating instructions for the Li-ion battery 

pack. 

2.1 Safety instructions for laser units

In Class 2 laser units, your eyes are usually protected from accidental, short-term expo-

sure to the laser beam by the eyelid-closing reflex and/or the reflex reaction to turn 

one’s head. If a laser beam hits your eye, deliberately close your eyes and move your 

head out of the path of the beam. Do not look into the direct or reflected beam.  

The STABILA laser goggles available for our laser units are not safety eyewear:  

their function is to improve the visibility of the laser beam. 

• 

Do not aim the laser beam directly at people! 

• 

Avoid dazzling other people with the unit! 

• 

Keep the unit out of the reach of children!

• 

If operating or adjustment equipment that has not been specified here is used, or 

if the unit is not operated in the ways described here, this may result in hazardous 

exposure to radiation! 

LASER

2

LASER RADIATION

DO NOT STARE INTO BEAM
510 - 635 nm / <1mW
CLASS II LASER PRODUCT

CFR 1040.10 AND CFR 1040.11

Содержание LAX 600 Series















Отзывы: