background image

4

GENERAL INFORMATION

• Clean a new pool as well as possible before filling pool and operating fil-

ter. Excess dirt and large particles of foreign matter in the system can
cause serious damage to the filter and pump.

Do not operate filter at water temperatures above 120°F (65.5°C).

NEVER operate this filter system at more than 50 pounds per square
inch (50 PSI/345kPa) pressure!

TABLE I - OUTLINE DIMENSIONS IN INCHES (mm)

Sand 

C

D     

E   

F

Model

No. of Clamps

S7S50   28-1/2(724)  42(1067)

7

36(914) 

53-1/2(1360)  2” NPT

S8S70   32-1/2(825)  42-1/4(1073)

8

40(1020) 54-1/4(1380) 2” NPT

TABLE ll - FILTER SPECIFICATIONS AND OPERATING INFORMATION

FILTER MODEL:

S7S50

S8S70

Filter Area

2.4 Ft.

2

(.223M

2

)

3.4 Ft.

2

(.316M

2

)

Flow Rate Range

33-48 GPM(125-182 L/m)

47-68 GPM(178-257 L/m)

Public Pool Flow Rate

48 GPM(182 L/m)

68 GPM(257 L/m)

Max. Operating Pressure

50 PSI(345 kPa)

50 PSI(345 kPa)

Freeboard (See Fig. 1B)*

11” (28 cm)

11” (28 cm)

Turnover in Hours:

6 Hours

17,200 Gal.(65 102 liters)

24,400 Gal.(92 354 liters)

8 Hours

23,000 Gal.(87 055 liters)

32,600 Gal.(123 391 liters)

10 Hours

28,800 Gal.(109 008 liters)

40,800 Gal.(154 428 liters)

Qty. of Media Required:

Cu. Ft.

2(56 540cm

3

)

3(84 960cm

3

)

Weight (Pounds)

200(90,7 kg)

300(136 kg)

* Freeboard is the open space between the top of the sand bed and the tank backwash outlet.

NOTICE: 1 cubic foot (28 320 cm

3

) of sand weighs approximately 100 lbs. (45,4kg). DO NOT

use a finer grade of sand than recommended.

RECOMMENDED SAND GRADES:

Use only: #20 Silica Sand, Size Range .40-.55mm., Uniformity Coefficient
less than 1.75.

NOTICE: Use of other sands will reduce filter performance, may damage
pump,and will void warranty.

Recommended:

1. Wedron Silica/Best Sand Co., Sand Grade: Wedron .45-.55mm.,

Effective Size .46mm, Uniformity Coefficient 1.22.

2. U.S. Silica - Silurian Filter Sand, Sand Grade.45-.55 mm., Effective Size

.48mm, Uniformity Coefficient 1.18.

Hazardous pressure.
Can cause severe 
injury or major 
property damage 
from tank blow up.

Release all pressure 
and read instructions
before working on filter.

A

B

C

D

E

INLET

OUTLET

7.812"

19.85 cm

9.19"

23.3 cm

F

SAND BED

11"

TANK

FLANGE

DISTRIBUTOR

11" (28 cm)

FREE BOARD

12.5"

31.75 cm

Figure 1 - Dimensions

Figure 2 - Freeboard measurement

0

10

20

30

40

50

60

70

80

0

1.0

2.0

3.0

4.0

Gallons Per Minute

P

ressure 

D

rop 

(PSI)

5.0

6.0

14.0

2.0

4.0

6.0

8.0

10.0

12.0

Pressure Drop (Feet)

S8S70

S7S50

015 0893

Содержание System 3

















Отзывы: