manualshive.com logo in svg

STA-RITE SR6000S, Руководство по установке и эксплуатации

Поделиться
Скачать
STA-RITE SR6000S Скачать руководство пользователя страница 14

 

14 

S

TA

-R

ITE 

I

NSTALLATION 

&

 

O

PERATION 

G

UIDE                

 

 

 

pH 
Feed 

pH 
Alarm 

Flow ORP 

Alarm 

ORP 
Feed 

CONDITION INDICATED 

 

 

 

 

 

Flow is detected through switch input. 

 

 

 

 

 

We have flow and pH pump is feeding. 

 

 

 

 

 

We have flow and ORP pump is feeding. 

 

 

 

 

 

We have flow and both pH and ORP pumps are feeding. 

 

 

 

 

 

We are in ph Menu. 

 

 

 

 

 

We are in ORP Menu. 

     We 

are 

in 

Advanced 

Menu. 

 

 

 

 

 

pH is in Alarm. 

 

 

 

 

 

1 second flash means pH pump is in overfeed. 

 

 

 

 

 

ORP is in Alarm. 

 

 

 

 

 

1 second flash means ORP pump is in overfeed. 

LED SUMMARY TABLE 

  

3.3   INITIALIZING THE SR6000S 

When initializing/turning on the SR6000S, it will perform a brief check of its internal 

system and check its memory for operation. It will also display the date code for the 
version of software that the system is currently using. (As listed below the software 

version is dated 02 17 03, or  Feb 17, 2003.) 
 
 
 

 

Note: When contacting Sta-Rite for technical support be sure to have this information 
available to give to them.  
 

3.4   READING DISPLAY 

During normal operation the reading display will show the actual values of pH and ORP in 
the water source as sensed by the probes. It will also show if and which of the chemical 

controller pumps should be feeding by lighting a Green LED.  If there is an alarm condition 
that will be displayed with a Red LED and Green flow LED shows whether the system has 

water flow or not.  

 

pH   

 

 

 

 

 

   ORP

 

 

 

 

 

 

 

 

021

703

Содержание SR6000S


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды