SSS Siedle ProSpec HD101, Инструкция по эксплуатации

Страница: 13 / 14

FORM NO. 56091054 - ProSpec HD101 / HD101DC - 13
10, 11 - DUST CUP AND BAG
The cloth bag and the dust cup play a very important role in the ef fi ciency
of the vacuum cleaner. The cloth bag allows air to move through the
cleaner while it traps dirt inside the cloth bag and the dust cup. When
dirt particles cling to the cloth bag they can restrict air
fl ow. If air cannot
pass through the cloth bag, no cleaning can take place regardless of how
powerful the unit. Some
fi ne particles can restrict air fl ow very quickly
and will decrease performance even before the dust cup appears to be
full. For that reason, when vacuuming powder,
fl our dust, or similar fi ne
substances, it may be necessary to turn off the cleaner and empty the
dust cup more often.
NOTE: Turn off the switch and unplug the electrical cord before emptying
the dust cup. Never operate the vacuum cleaner without the dust cup
latched in place.
1 Unhook the clip from the top of the cloth bag.
2 Shake the cloth bag to release dust clinging inside.
3 Release each latch, one on either side of the handle. In order to
release each latch, push down on the secondary lock. Then lift
up on the bottom of the latch; and
fi nally, pull the top of the latch
forward.
4 Lift the lid, swing it up and outward.
5 Reach in, grasp the dust cup and pull it out of the support.
6 Empty contents in a suitable container. (If desired, the cup can be
washed in warm water using a mild soap solution. Be sure the cup
is completely dry before replacing.)
7 Place the cup into the support, swing the lid shut, and fasten each
latch.
8 Hook clip to top of bag (refer to item 1).
CLEAN UP AND STORAGE
Store the machine in a cool dry place. Wind the extension cord in a circle
and hang on the cord hooks provided on the machine. Be sure not to
wind the cord tighter than necessary.
Avoid prolonged exposure of machine to freezing temperatures during
storage or transporting.
MAINTENANCE
WARNING!
BEFORE ANY SERVICING TO AVOID POSSIBLE INJURY OR
ELECTRIC SHOCK, DISCONNECT THE POWER CORD FROM
THE ELECTRICAL OUTLET.
CAUTION!
Keep the area behind each latch free of dust or obstructions that
would prevent it from locking securely.
BRUSH ROLL BELT REPLACEMENT
CAUTION!
Belt and pulley become hot during normal use.
The belt should be checked regularly. Replace belt if it is stretching,
cracking or slipping.
Remove the bottom chrome plate by turning the two cam locks on each
side. Remove the worn belt from the drive motor pulley. Remove the
brush roll from the base, and slide off worn belt. Slip new belt around
brush roll and reinstall into machine. Install belt around drive pulley with
low side in groove. Be sure belt is installed correctly or brush roll will turn
backwards. Replace chrome cover.
NOTE: Be sure brush roll with offset belt drive is oriented correctly, with
the shorter length to the left. Arrows on brush roll end-caps indicates the
top of cap and shows installation direction. Cut away any hair or thread
wound around the brush roll or the belt pulley because the buildup could
cause the belt to rotate unevenly.
BRUSH STRIP REPLACEMENT
To replace, remove the bottom chrome plate by turning the two cam locks
on each side and remove brush roll from machine. Remove nuts and end
caps. Slide out worn brush strips and replace. Reassemble brush roll
and reinstall in machine.
NOTE: Brush strips are different lengths. Arrows on brush roll end caps
indicates the top of cap and shows installation direction.
headlight replacement
FAN SCROLL
The clear fan scroll attached to the underside of the base can be removed
and cleaned. Remove the chrome plate and brush roll belt from pulley.
Remove the two screws on either side of the clear scroll, press the cam
locks outward and lift the scroll from the base. Dirt should clear easily,
though some scraping may be needed.
Be sure the gasket is in place. Reinstall by placing the rear-end between
the rear wheels and seat
fi rmly. Reinstall belt and chrome plate.
CARBON MOTOR BRUSHES
Have your Triple S dealer check the carbon motor brushes once a year
or after 500 operating hours.
IMPORTANT!
Motor damage from failure to service the carbon brushes is not
covered under warranty.