ELECTRICAL SAFETY
1 . The unit should be connected to an electrical supply that
is surge protected and in compliance with local codes .
2 . The unit is fitted with a standard three-prong plug with a
15A circuit breaker .
3 . Ensure that the correct supply voltage is available before
switching on the unit .
4 . Ensure the voltage being used corresponds with the volt-
age on the machine parts . The standard motors are 115V,
1Ph, 50/60Hz and 240V, 1Ph, 50/60Hz
5 . Check the AC cable for nicks and cuts (regularly inspect
the cable to ensure it is in good condition) .
6 . Do not pull the portable unit by the electrical cable or
the hose .
7 . Only qualified personnel may access electrical system .
8 . There are no serviceable parts in the fan unit .
REPLACEMENT PARTS
This unit was designed, engineered, and built with operator
safety and optimum performance as primary objectives .
Substitution of non-OEM parts may jeopardize safety, void
any warranties, and adversely impact performance .
After you have unpacked the Jet-Kleen Limited and familiar-
ized yourself with this manual, you may proceed to instal-
lation and setup of the unit . Set up the portable Jet-Kleen
Limited where you intend to use it, making sure there is an
available electric supply and adequate clearance .
The Jet-Kleen Limited should be placed so that the four feet
are in contact with a level or flat surface .
The Jet-Kleen Limited should be plugged into an appropriate
grounded outlet . Turn the switch to ON to operate the Jet-
Kleen Limited . Turn switch to off when finished .
Nozzle Assembly Attachment
To attach the nozzle assembly, follow these simple instruc-
tions:
1 . Leave the locking ring open (unscrewed) as shown
in Figure 2 . If the locking ring is in the closed posi-
tion, rotate the locking ring on the swivel connector
(Figure 2) counterclockwise 180° until it clicks .
2 . Push the new nozzle assembly firmly into place .
3 . Close the locking ring by rotating it 180° back to its
original position .
Nozzle Assembly Detachment
To detach the nozzle assembly:
1 . Rotate the locking ring on the swivel connector (Figure
2) counterclockwise 180° until it clicks .
2 . Depress the quick release ring .
3 . Pull the quick-release fitting toward the hose away from
the gun assembly .
4 . Twist and pull out the gun assembly .
Follow similar procedures when replacing the
hose by using the locking ring and quick-release
fitting on the hose end of the swivel connector.
Optional Wall-Mount Bracket
To install the Optional Wall-Mount Bracket to your Jet-Kleen
Limited unit:
1 . Remove the four rubber feet from the Jet-Kleen Limited
using an Allen wrench .
2 . Leave the mounting hardware attached to the Jet-Kleen
Limited unit as this will be used to attach the wall-
mount bracket .
3 . Attach the Optional Wall Mount Bracket to the mounting
hardware using the four flathead screws provided with
the bracket .
4 . Secure using a flathead screwdriver .
The Jet-Kleen Limited may now be wall-mounted in a loca-
tion of your choice using appropriately-rated fasteners .
Figure 2. With locking ring unscrewed (as pictured) depress quick release ring
then pull quick-release fitting toward hose.
Locking ring
Quick-release fitting
Handle
assembly
i
nsTallaTion
& s
eTup
Swivel connector
IMPORTANT
TO PREVENT OVERHEATING AND POSSIBLE PERMANENT DAM-
AGE TO THE UNIT, DO NOT RUN THE JET-KLEEN LIMITED CONTINU-
OUSLY FOR MORE THAN THREE HOURS.
SPECIALIZED
SAFETY
PRODUCTS
A Division of The A.W.T. World Trade Group
4321 N. Knox Ave., Chicago, IL 60641 USA
773.777.7100 • Fax:773.777.0909
www.specializedsafetyproducts.com
J
et
-K
leen
tm
5
Installation & Operation Manual
p
S
S
A Product of
