manualshive.com logo in svg

SSB-Electronic Zeus-1, Руководство по эксплуатации

Поделиться
Скачать
SSB-Electronic Zeus-1 Скачать руководство пользователя страница 25

Software description

Main window

If   one   of   the   parameters   (voltage   or   current)   falls   below   the   die   minimum

permitted   values,   the   color   of   the   display   changes   from   green   to   yellow.   The
transceiver will still work, but its parameters may be degraded, compared to the
specifications.

In the case you encounter a current consumption out of the permitted range,

please stop using the transceiver and contact your dealer.

36 Transceivers temperature indicator

The   display   informs   about   the   mean   temperature   inside   the   transceiver   and

therefore   it   is   a   bit   lower   as   the   temperature   of   the   transmitters   final   stage
transistors. This way the temperatures of all sensitive components of the transceiver
are controlled and the normal thermal state of the final stage ensured.

The background color of the temperature indicator changes in the same way as in

the   voltage   and   current   indicator.   If   the   maximum   temperature   values   are
exceeded, operation of the transceiver will be stopped. 

37 Data transfer rate indicator

The indicator shows the data speed via USB interface.
The   speed   depends   on   the   spectrum   bandwidth.   Because   of   the   maximum

resolution of the displays is used for bandwidths up to 100 kHz, the 100 kHz setting
requires the maximum USB speed.

Bandwidth

Data speed

Bandwidth

Data speed

10 kHz

0,8 Mb/s

320 kHz

4,2 – 4,3 Mb/s

20 kHz

1,6 Mb/s

800 kHz

4,2 – 4,3 Mb/s

40 kHz

3,3 Mb/s

1,6 МHz

4,2 – 4,3 Mb/s

100 kHz

6,1 — 6,2 Mb/s

4 МHz

4,2 – 4,3 Mb/s

160 kHz

4,2 – 4,3 Mb/s

For various reasons the data speed can be lower than needed. This means that

the ZeusRadio software gets less data than needed for proper operation, which is
manifested by audio dropouts and very high noise floor.

Also the use of a too long or inferior USB cable or a PC with an insufficient CPU

may be the cause of too low transfer rates. Avoid using of any USB hubs (also active
USB Hubs!).

SSB-Electronic GmbH ©     Page 25 of 88      V2.8.1     C

ontent is protected by Copyright.                 

Содержание Zeus-1

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды