SRAM RockShox RS-1 Скачать руководство пользователя | Manualshive

Страница: 49 / 59

background image

49

Accelerator Damper™ Service

Rotate the rebound adjuster

counter-clockwise

to the open position.

The rebound adjuster screw will click as it is adjusted.

Pour suspension fluid into the cartridge tube.

Pour the fluid slowly to avoid introducing air into the fluid.

Slowly cycle the rebound shaft a few times to bleed the system.

⚠

CAUTION- EYE HAZARD

Pull the rebound shaft down slowly. Failure to do so can result in fluid
ejecting from the cartridge tube. Wear safety glasses.

Thread the knurled collar onto the Connectamajig™ until it is finger tight.
Push the XLoc™ button in to the compressed (unlocked) position.

19

2.5 mm

20

75mL

5wt

21

22

«
...
47
48
49
50
51
...
»

Содержание RockShox RS-1




























































Отзывы:

Нет отзывов

Похожие инструкции для RockShox RS-1

Бренд: Calsense Страницы: 6

Бренд: Danfoss Страницы: 4

Бренд: PACIFIC CYCLE Страницы: 112

Бренд: E+E Elektronik Страницы: 14

Бренд: E+E Elektronik Страницы: 26

Бренд: E+E Elektronik Страницы: 28

Бренд: E+E Elektronik Страницы: 2

Бренд: BW Страницы: 8

PRIME DESIGN VCR 326

Бренд: Safe Fleet Страницы: 16

Prime Design VBC PC11

Бренд: Safe Fleet Страницы: 8

Бренд: Saful Страницы: 7

Бренд: Saft Страницы: 66

Prime Design AR1418

Бренд: Safe Fleet Страницы: 4

Бренд: T-Home Страницы: 52

WorkCentre Pro 123

Бренд: Xerox Страницы: 4

6130N - Phaser Color Laser Printer

Бренд: Xerox Страницы: 2

Бренд: Varta Страницы: 132

Бренд: dol sensors Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды