SRAM RockShox Deluxe RLR Скачать руководство пользователя страница 52

Страница: 52 / 58

Shock Eyelet Assembly

S h o c k E y e l e t A s s e m b l y

E y e l e t B u s h i n g I n s t a l l a t i o n

Apply a light layer of grease to the outside of the new bushing.

Position the shaft eyelet and eyelet bushing between the soft jaws of a

vise. Slowly turn the vise handle to begin pressing the eyelet bushing

into the shaft eyelet.

Check the alignment of the bushing as it enters the eyelet. If the

bushing starts to enter the eyelet at an angle, remove the bushing

from the eyelet, regrease the bushing, and repeat this step until the

bushing enters the eyelet straight.

Continue to press the eyelet bushing until it is seated in the

shaft eyelet.
Remove the shock from the vise and repeat the installation process for

the other bushing and eyelet.

Содержание RockShox Deluxe RLR



























































Результаты поиска

Содержание RockShox Deluxe RLR

Отзывы:

Похожие инструкции для RockShox Deluxe RLR

Бренды по названию

Популярные бренды

SRAM RockShox Deluxe RLR, Руководство по обслуживанию

Результаты поиска

Содержание RockShox Deluxe RLR

Отзывы:

Похожие инструкции для RockShox Deluxe RLR

Бренды по названию

Популярные бренды