SRAM RockShox Deluxe RLR Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 58

SRAM RockShox Deluxe RLR Скачать руководство пользователя страница 47

47

Shock Assembly and Bleed

Install a new damper body bleed screw into the damper body eyelet.

Tighten the bleed screw to 1.1 N

·

m (10 in-lb).

Spray isopropyl alcohol on the damper body and clean it with a rag.

Remove the shock from the vise. Pour the oil out of the IFP reservoir.

Wipe the inside of the IFP reservoir with a rag.

NOTICE

Do not spray isopropyl alcohol into the reservoir. Isopropyl alcohol can

cause o-rings to become brittle and crack.

Clamp the shaft eyelet into the vise so the shock is vertical

To check the bleed quality, install the IFP Height Tool into the IFP

reservoir and apply force to the IFP Height Tool (approximately

25 lbs). The IFP should feel firm and should not compress. If the bleed

check window is compressed beneath the edge of the reservoir, the

system will need to be re-bled. To re-bleed the system, remove the IFP

reservoir and the IFP, and return to step 4.

Apply a thin layer of grease to the IFP reservoir cap o-ring. Push the IFP

reservoir cap into the IFP reservoir until the retaining ring groove

is visible.

23

T10 TORX®

T10 TORX

1.1 N•m (10 in-lb)

24

IFP Height Tool

Bleed Check Window

25

26

«
...
45
46
47
48
49
...
»

Содержание RockShox Deluxe RLR



























































Отзывы:

Нет отзывов