SRAM G2 RSC Скачать руководство пользователя страница 40

Страница: 40 / 42

G2 Ultimate Lever Bearing Replacement

To install a new bearing insert the threaded bearing press into the lever

body with the flat face toward the bearing bore.

Place a new bearing into the bearing bore.
Install the bearing press onto the bearing press bolt and thread into the

threaded bearing press.

Do not reuse bearings that have been removed.

Tighten the bearing press bolt until the bearing is pressed into the

lever body.
Unthread the bearing press bolt to remove the tools from the lever

body.
Repeat steps 5-7 to install the other new bearing.

To continue with lever service, go to

Piston Assembly Removal, page 24

If you do not need to service your lever internals, go to

Lever Blade Installation, page 31

to assemble the brake lever.

2.5

20 mm or 15 mm Thru Axle

Содержание G2 RSC











































Результаты поиска

Содержание G2 RSC

Отзывы:

Похожие инструкции для G2 RSC

Бренды по названию

Популярные бренды

SRAM G2 RSC, Руководство по обслуживанию

Результаты поиска

Содержание G2 RSC

Отзывы:

Похожие инструкции для G2 RSC

Бренды по названию

Популярные бренды