background image

A.0200.301 – IM-TA/03.00 EN (03/2007)

20

14.0 Trouble shooting

Cause   

                                                  Action to be taken

 

 

 

Pump does not rum

The exhaust port (silencer) of pump is 

 

Check and clean the exhaust port and 

 

clogged with sludge. 

 

 

 

silencer.  

 

 

 

Air is not supplied. 

 

 

 

Start the compressor and open the air valve  

   

 

 

 

 

 

and air regulator.

The supply air pressure is low. 

 

 

Check the compressor and the configuration  

   

 

 

 

 

 

of air piping.

Air leaks from connection parts.   

 

Check the connection parts and tightness of  

   

 

 

 

 

 

bolts.

Air piping or peripheral equipment is  

 

Check and clean the air piping.   

 

clogged with sludge. 

 

 

 

 

The flow valveon the discharge side is not  

Open the flow valve on the discharge side. 

open.
The spool stopped in neutral position. 

 

Press the reset button.

The fluid piping is clogged with sludge. 

 

Check and clean the fluid piping. 

The pump is clogged with sludge.  

 

Disassemble the casing, check and clean.

Pump runs, but fluid does not come out

The sucion lift or discarge head is long.   

Confirm the piping configuration and  

 

   

 

 

 

 

 

shorten the length. 

 

 

 

 
The discharge-side fluid piping (including  

Check and clean the fluid piping.  

 

the strainer) is clogged with sludge. 

 

 

The valve on the suction side is not open.   

Open the valve on the suction.

The pump is clogged with sludge.  

 

Disassemble the casing, check and clean.

The ball and valve seat are worn out or   

Disassemble the manifold, check and  

 

damage.  

 

 

 

 

replace parts. 

 

 

 

 

   

 

 

 

 

Flow (discharge volume) decreased

The supply air pressure is low. 

 

 

Check the compressor and configuration   

   

 

 

 

 

 

of air piping.

Air piping or peripheral equipment is 

 

Check and clean the air piping.   

 

clogged with sludge.

The discharge-side flow valve opens 

 

Adjust the discharge-side flow valve. 

 

differently.
Air is taken in together with fluid. 

 

Replenish fluid and check the configuration 

   

 

 

 

 

 

of the sucion-side piping.

Cavitation occurs. 

 

 

 

Adjust the supply air pressure and discharge  

   

 

 

 

 

 

pressure, and shorten the sution lift.

Chattering occurs. 

 

 

 

Adjust the supply air pressure and discharge  

   

 

 

 

 

 

pressure. Reduce inlet flow valve to adjust-  

   

 

 

 

 

 

ing liquid pressure and volume.

   

 

 

 

 

 

 

 

 

Содержание JOHNSON PUMP TopAir TA-15




























































Отзывы: