manualshive.com logo in svg

SPX FLOW W71, Инструкция по эксплуатации, Страница: 32 / 64

Поделиться
Скачать
SPX FLOW W71 Скачать руководство пользователя страница 32

Maintenance

Waukesha Cherry-Burrell Brand W71/W72RS Sch. 5 Mix Proof Valves

Page 32

95-03091

08/2018

Lower Stem Tef Flow

®

 P Seat Removal 

W71 Lower Stem Tef Flow

®

 P Seat Removal

1. With the lower stem in hand, take note of the orientation of 

the Tef Flow

®

 P seat. 

2. Remove the balancer from the bottom of the stem.

3. Install the PTFE installation base (item 4) over the stem, 

positioned so that the chamfered side of the base rests 
snugly on top of the lower stem plug. Make sure the flat side 
of the base faces away from the plug.

4. Invert the stem so that it is oriented with the stem facing 

toward the floor. 

5. While holding the installation base (item 4) in place on the 

stem, carefully set the pins of the Tef Flow

®

 P seat removal 

tool (item 2) on the existing seat ring. Make sure that the pins 
rest only on the Tef Flow

®

 P seat, not the seat plug, as this 

can cause damage to the metal plug.

6. Place the protective puck (item 3) on top of the removal tool 

(item 2). With the stem facing down, carefully place the 
components on an arbor press.

7. Apply even pressure to the top of the protective puck (item 3) 

until the seat is cut into three pieces.

8. Carefully retrieve the stack from the arbor press, removing 

the tools and seat pieces from the stem in reverse order.

9. Inspect the stem and stem plug for damage. Clean up any 

minor scratches with an emory cloth, if needed.

Figure 33 - Lower Stem Tef Flow

®

 P 

Seat Removal (Kit # )

* for 2" W71 ODT valves only

VA100-811 a

1*

3

4

2

Содержание W71

































































Отзывы:

Нет отзывов