SPX FLOW W71 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 64

SPX FLOW W71 Скачать руководство пользователя страница 29

Waukesha Cherry-Burrell Brand W71/W72RS Sch. 5 Mix Proof Valves

Maintenance

08/2018

95-03091

Page 29

Radial Seat Ring

Replacement (for W72RS

Lower Stem)

1. Remove the lower stem radial seal by carefully prying up and

cutting the O-ring. Do not scratch or nick the metal seating
surface.

Maintenance Video 11: Radial Seal Removal

2. Clean the radial seal groove after removal.

3. Ensure that the vent port in the back of the groove is clean

and unblocked.

4. Lubricate the O-ring seal and expand it over the stem groove.

5. Place the assembly tool over the stem, ensuring proper tool

orientation. Extrude the O-ring seal into the groove by evenly
tightening the cap screws on the installation tool.

6. Remove the tool. The dovetail groove permanently retains

the O-ring seal.

Maintenance Video 12: Radial Seat Ring Replacement

For a list of installation tools, see Figure 29 below and
“Installation Tools” on page 57.

Figure 28 - Radial Seal Installation

1

2

3

VA100-507

Figure 29 - Radial Seal Insertion Collar Tool (for W72RS Valves)

VA100-664

Valve Size

2"

3"

4"

Part No.

Valve Size

6"

Part No.

«
...
27
28
29
30
31
...
»

Содержание W71

































































Отзывы:

Нет отзывов