manualshive.com logo in svg

SPX FLOW Power Team PB10 Series, Перечень деталей и инструкция по эксплуатации

Поделиться
Скачать
SPX FLOW Power Team PB10 Series Скачать руководство пользователя страница 11

11

© SPX FLOW, Inc.

Form No. 1001044

Rev. 2    Jan. 25, 2019

Setup Instructions continued
3.  Hydraulic Lines and Fittings.

• 

Hydraulic lines and fittings can restrict flow to a cylinder or hydraulically actuated device. The 

 

restricting or slowing of the fluid flow causes back pressure that slows the device’s return. Return speed 

also varies because of the application, condition of the cylinder or device, inside diameter of hose or 

fitting, length of the hose, and the temperature and viscosity of the hydraulic fluid. 

•  Tubes and Hoses should be routed in such a way that they can easily be serviced or removed as well 

as provide the least resistance to fluid flow. See below for recommended routing configurations.

TUBING

HOSES

CORRECT

INCORRECT

CORRECT

INCORRECT

4.  18VDC Battery & Charger

NOTE:  

New batteries must be charged before first use. Approx. 60 minutes of charging = 100% battery 

fuel.

A.  Ensure battery charger is plugged in.

B.  Slide battery pack into charger as shown and allow battery to charge.

C.  Once battery is adequately charged it can be installed on pump unit as shown. 

D.  To remove the battery from the pump unit press the release buttons on the sides of the battery.

E.  Slide the battery out of the pump unit as shown. 

B.

A.

Содержание Power Team PB10 Series













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды