background image

GAS ENGINE (WHERE APPLICABLE)

Always place pump outside of structure in fresh air.  Keep all
solvents away from the engine exhaust.  Never fill fuel tank
with a running or hot engine.  Hot surface can ignite spilled
fuel.  Always attach ground wire from pump unit to a grounded
object, such as a metal water pipe.  Refer to engine owner’s
manual for complete safety information.

HAZARD: EXPLOSION HAZARD DUE TO INCOMPATIBLE

MATERIALS - Will cause severe injury or
property damage.

PREVENTION:

• Do not use materials containing bleach or chlorine.
• Do not use halogenated hydrocarbon solvents such as

mildewcide, methylene chloride and 1,1,1 -
trichloroethane.  They are not compatible with aluminum.

•  Contact your coating supplier about the compatibility of

material with aluminum.  

HAZARD: HAZARDOUS VAPORS -  Paints, solvents,

insecticides, and other materials can be
harmful if inhaled or come in contact with the
body.  Vapors can cause severe nausea,
fainting, or poisoning.

PREVENTION:

• Use a respirator or mask if vapors can be inhaled.  Read

all instructions supplied with the mask to be sure it will
provide the necessary protection. 

• Wear protective eyewear.
• Wear protective clothing as required by coating

manufacturer.

HAZARD: GENERAL - This product can cause severe

injury or property damage.

PREVENTION:

• Read all instructions and safety precautions before

operating equipment.

• Always disconnect the motor from the power supply

before working on the equipment (electric models only).

• Follow all appropriate local, state, and national codes

governing ventilation, fire prevention, and operation. 

• The United States Government Safety Standards have

been adopted under the Occupational Safety and Health
Act (OSHA).  These standards, particularly part 1910 of
the General Standards and part 1926 of the Construction
Standards should be consulted.

• Use only manufacturer authorized parts.  User assumes

all risks and liabilities when using parts that do not meet
the minimum specifications and safety devices of the
pump manufacturer.

• Before each use, check all  hoses for cuts, leaks, abrasion

or bulging of cover.  Check for damage or movement of
couplings. Immediately replace the hose if any of these
conditions exist.  Never repair a paint hose. Replace it
with another grounded high-pressure hose.

• All hoses, swivels, guns, and accessories must be rated at

or above 3300 PSI/22.8 MPa.

• Do not spray outdoors on windy days.
• Wear clothing to keep paint off skin and hair.
• Always unplug cord from outlet before working on

equipment.

• Do not use this equipment to spray water or acid.

Do not lift by cart handle when loading or unloading.

CAUTION

Gasoline Engine Safety

The engine exhaust from this unit contains chemicals
known to the State of California to cause cancer, birth
defects, or other reproductive harm.

1. Gas engines are designed to give safe and dependable

service if operated according to instructions.  Read and
understand the engine Owner's Manual before operating
the engine.  Failure to do so could result in personal injury
or equipment damage.

2. To prevent fire hazards and to provide adequate

ventilation, keep the engine at least 1 meter (3 feet) away
from buildings and other equipment during operation.  Do
not place flammable objects close to the engine.

3. Children and pets must be kept away from the area of

operation due to a possibility of burns from hot engine
components or injury from any equipment the engine may
be used to operate. 

4. Know how to stop the engine quickly, and understand the

operation of all controls.  Never permit anyone to operate
the engine without proper instructions. 

5. Gasoline is extremely flammable and is explosive under

certain conditions. 

6. Refuel in a well-ventilated area with the engine stopped.

Do not smoke or allow flames or sparks in the refueling
area or where gasoline is stored. 

7. Do not overfill the fuel tank.  After refueling, make sure the

tank cap is closed properly and securely. 

8. Be careful not to spill fuel when refueling.  Fuel vapor or

spilled fuel may ignite.  If any fuel is spilled, make sure the
area is dry before starting the engine. 

9. Never run the engine in an enclosed or confined area.

Exhaust contains poisonous carbon monoxide gas;
exposure may cause loss of consciousness and may lead
to death. 

10. The muffler becomes very hot during operation and

remains hot for a while after stopping the engine.  Be
careful not to touch the muffler while it is hot.  To avoid
severe burns or fire hazards, let the engine cool before
transporting it or storing it indoors. 

11. Never ship/transport unit with gasoline in the tank.

WARNING

© SprayTECH.  All rights reserved.

3

Содержание GPX 1600





























Отзывы: