12
1-800-732-0144
WWW.SPORTDOG.COM
13
MODE
UPPER BUTTON
FUNCTION
LOWER BUTTON
FUNCTION
SIDE BUTTON
FUNCTION
NUMBER OF
DOGS
1*
Continuous stimulation
(Level set by Intensity Dial)
OR
Vibe if V/T on dial
Momentary stimulation
(Level set by Intensity Dial)
OR
Vibe if V/T on dial
Tone only
1
2
Continuous stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
Momentary stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
Vibe only
1
3
Dog 1:
Continuous stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
Dog 2:
Continuous stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
Dog 3:
Continuous stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
3
4
Dog 1:
Continuous stimulation
(Level set by Intensity Dial)
OR
Vibe if V/T on dial
Dog 2:
Continuous stimulation
(Level set by Intensity Dial)
OR
Vibe if V/T on dial
Dog 3:
Continuous stimulation
(Level set by Intensity Dial)
OR
Vibe if V/T on dial
3
5
Continuous stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
Momentary stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
N/A
1
6
Continuous stimulation
(Level set by Intensity Dial)
OR
Vibe if V/T on dial
Momentary stimulation
(Level set by Intensity Dial)
OR
Vibe if V/T on dial
N/A
1
7
Continuous stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
Momentary stimulation
(Level set by Intensity Dial)
OR
Tone if V/T on dial
Locate Remote Beeper**
1
V/T
(ID CODE)
N/A
N/A
(See STEP 7)
N/A
* Factory default mode.
** Locate Remote Beeper: The Side Button turns run mode off and locates the Remote Beeper. To enable run mode
again, press and hold the Side Button for 3 seconds.
STEP :: 05
MATCH THE COLLAR RECEIVER AND REMOTE TRANSMITTER
To match the Collar Receiver to work with a new Remote Transmitter or to match a new Collar Receiver to work with
your existing Remote Transmitter:
1.
Turn the Collar Receiver off.
2.
Press and hold the power button. After the Receiver Indicator Light and the OLED Display have turned off,
release the power button.
3.
Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light flashes 5 times.
Once the Receiver Indicator Light has flashed 5 times, the Collar Receiver has been matched and will begin
flashing as normal. If the Receiver Indicator Light doesn’t flash 5 times, start over from 1.
Note: Your Collar Receiver will need to be in either
Training
or
C Train
modes.
STEP :: 06
PROGRAM THE SYSTEM FOR MULTI-DOG OPERATION
SportDOG Brand
™
Add-A-Dog
™
Collar Receiver(s) must be purchased to train additional dogs (up to 3).
Note: Your Collar Receiver will need to be in either
Training
or
C Train
modes.
1.
Program the Remote Transmitter to mode 3 or 4 (see page 12).
2.
Program the first Collar Receiver.
A. Turn the Collar Receiver off.
B. Press and hold the power button. After the Receiver Indicator Light and the OLED Display have turned off,
release the power button.
C. Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light flashes 5
times. If the Receiver Indicator Light doesn’t flash 5 times, start over from A.
3.
Program the second Collar Receiver using A through C above, but using the Lower Button in place of the Upper
Button.
4.
Program the third Collar Receiver using A through C above, but using the Side Button in place of the Upper
Button.
STEP :: 07
CHANGE ID CODES
An ID Code is the signal identification between the Remote Transmitter and Collar Receiver. Each is programmed in
1 of 2,000 ID Codes from the factory. The C Train
™
system has the flexibility to program two or more Remote
Transmitters to the same ID Code, allowing them to both control one Collar Receiver. There are 64 programmable
ID Codes available.
TO MANUALLY PROGRAM A REMOTE TRANSMITTER’S ID CODE FOLLOW THESE STEPS:
1.
Turn the Intensity Dial to V/T, and then press and release the Mode Button on the back of your Remote
Transmitter. This doesn’t change the mode, so the current mode will still be active after the ID change is
complete.
2.
Once the Mode Button is released, the Transmitter Indicator Light will illuminate solid green and stay on for
15 seconds.
3.
While the green Indicator Light is on, turn the Intensity Dial to select the 1st digit of the ID and then press and
release the Side Button. The green Indicator Light will flash rapidly confirming selection.
4.
Again, while the green Indicator Light is on, turn the Intensity Dial to select the 2nd digit of the ID and then
press and release the Side Button. The green Indicator Light will flash rapidly confirming selection. The 2nd
digit is optional and, if not desired, wait until the green light turns off and refrain from pressing the Side
Button.
5.
At the end of 15 seconds, or after the second press of the Side Button, the green Indicator Light will turn off and
the ID of the unit will be updated. At this point, the unit will be in the same mode it was in prior to setting the ID.
6.
Upon changing the ID Code, you’ll need to match the Collar Receiver to the Remote Transmitter (see STEP 5 on
page 12).
