background image

REPAIR MANUAL 

Page:  i

 

This Repair Manual is intended for persons having electrical and mechanical training and a level of knowledge 

of these subjects generally considered acceptable in the Appliance Service Industry. Splendide  cannot  be      
responsible, nor assumes any liability for injury or damages of any kind arising from the use or misuse of     

the information contained in this Repair Manual. 
 

If you have any questions regarding the proper diagnosis, repair or operation of any Splendide Appliance, please 
contact Splendide Division Westland Sales at 1-800-356-0766.  

 

 

SERVICING SAFEGAURDS: 

 

To avoid personal injury and/or property damage, it is important that safe servicing practices be observed at all times.  Examples of 

safe service practices are listed below but are not limited to the following: 

 
1)    Never attempt a product repair if you have any doubts as to your ability to complete the repair in a safe and   

       satisfactory manner. 

 

2)  Before servicing or removing an appliance: 

 

 

  - Disconnect power to the appliance. 

 

  - Turn off the gas / LP supply. 

 

  - Turn off the water supply. 

 

3)  Never interfere with the proper operation of any safety device. 

 
4)  Use only genuine factory replacement parts as substitutions may interfere with compliances to home safety codes or standards. 

 

5)  It is extremely important that all safety ground connections be reestablished prior to the completion of the service call. Failure to 

do so will result in a hazardous condition being created. 

 

6)  Prior to returning the appliance back into active service, ensure the following: 

 

          - All electrical connections are correct and secure. 

          - Electrical leads are properly dressed and secured away from sharp edges, high temperature components and moving parts. 

          - All non-insulated electrical terminals, connectors, heaters, etc. are adequately spaced away from metal parts or panels. 
          - All safety grounds (both internal and external) are correctly and securely connected. 

          - All access panels are properly and securely reassembled. 

     

 

SAFE SERVICE PRACTICES 

AW 120 / AW 122 / AW 125 
AWD 120 / AWD 121 / AWD 129 

Содержание Ariston AW120



















Отзывы: