background image

REPAIR MANUAL 

Page:  13

 

14.  FAULT CODES 

A repair fault is signaled by the continuous rotating of the Program Knob and the flashing of the Door Locked LED. The Fault Code is        

determined by counting the sequence of individual flashes of the LED (2 flashes = F2).  The LED will flash the Fault Code sequence 
and then delay for approximately eight (8) seconds, repeating the Fault Code sequence and eight second delay continually.  

 

TECH NOTE: The unit can be turned off without harm and the Fault Code sequence will repeat when power is reapplied.  

F1. Triac 

Short 

 

 

 

 

 

 

 

 

 

 

Replace Control Board. 

 

F2. Main 

Motor 

 

 

 

Check Main Motor connections. 

 

Replace Main Motor. 

 

Or, replace Control Board. 

 
F3.  NTC (Water Temp) Open / Short 

 

 

 

Check wiring continuity to Control Board. 

 Replace 

NTC. 

 

Or, replace Control Board. 

 
F4. Pressure 

Switch 

 

 

 

Check wiring continuity to Control Board. 

 Replace 

Pressure 

Switch. 

 

Or, replace Control Board. 

 
F5.  Blocked Drain Motor or Pressure Switch shorted in Empty position 

 

 

 

Check Drain Hose. 

 

Check Drain Motor clean out for obstruction. 

 

Check voltage at Drain Motor. 

 

Check Pressure Switch wiring continuity. 

 

Replace Drain Motor / Pressure Switch. 

 

Or, replace Control Board. 

 
F6. Program 

Selector 

 

 

 

Check wiring continuity to Control Board. 

 Replace 

Program 

Selector. 

 

Or, replace Control Board. 

 
F7. Not 

Used 

 
 

 

F8.  Pressure Switch Shorted in Full Position 

 

 

 

Check Pressure Switch wiring continuity. 

 

Or, replace Pressure Switch. 

 

Or, replace Control Board. 

 
 

 

F9.  Control Board Error  

 

 

 

Incorrect version of Control Board or EEPROM. 

 

Change Control Board and EEPROM. 

 
F10. Pressure 

Switch 

Shorted 

 

 

 

Check wiring continuity to Control Board. 

 Replace 

Pressure 

Switch. 

 

Or, replace Control Board. 

 
F11. Drain 

Motor 

 

 

 

 

Check wiring continuity to Control Board. 

 

Check Drain Motor clean out for obstruction. 

 

Voltage check at Drain Motor. 

 

Check Pressure Switch. 

 Replace 

Drain 

Motor. 

 

Or, replace Control Board. 

 
F12. Not 

Used 

 

F13 - F16 Apply Only to AWD 120 

 
F13.  NTC (Dryer Temp) Open / Short 

 

 

 

Check wiring continuity to Control Board. 

 Replace 

NTC. 

 

Or, replace Control Board. 

 
F14.  Dryer Heating Element is Open 

 

 

 

Check Dryer Heating Element continuity. 

 

Check wiring from Element to Control Board. 

 Replace 

Heating 

Element. 

 

Or, replace Control Board 

 
F15.  Dryer Heating Element Relay Shorted 

 

 

 

Check Dryer Heating Element continuity. 

 

Check wiring from Element to Control Board. 

 

Replace Control Unit. 

 
F16. Not 

Used 

AW 120 / AW 122 / AW 125 
AWD 120 / AWD 121 / AWD 129 

Содержание Ariston AW120



















Отзывы: