background image

 

 9 

2.  WORK ZONE SAFETY 

  The work zone must be kept clear of all persons not authorized to be there. If other people must 

be in the work area they too must wear all necessary personal protective equipment and must be 
aware of the existing hazards / risks.  

  This unit must not be operated in hazardous areas. Also to prevent fire hazards it must not be 

operated near inflammables such as petrol, grain dust, solvents, thinners etc. 

  When operating the unit make sure  the operating area is not releasing health or environmental 

hazardous substances (E.g. asbestos, oil etc) 

3.  EQUIPMENT SAFETY 

  Never exceed the maximum working temperature and pressure as indicated on the unit data plate 

and in this manual. 

  Only use this unit with cleaning chemicals recommended by Spitwater. The use of other cleaning 

agents or chemicals may adversely affect the safety of the unit. 

  Never operate the unit without water as even a brief operation without it will cause severe damage 

to the pump and other components. 

  When finishing work, switch OFF the unit and release any trapped pressure in the hose and 

engage the gun trigger lock. 

  Never leave the unit unattended while it is running. 

  Never lock the spray gun trigger in the open position. 

  Never use accessories or spare parts that were not designed for use with this unit as this could 

cause damage to the unit.  Spitwater recommends the use of original accessories and spare parts 
available through Spitwater and its extensive dealer network. 

  Never use a nozzle size other than that specified in the technical data. Using the wrong size 

nozzle could damage the unit. 

  Keep flammable materials away from, and do not place anything on the unit while it is running. 

 
 
 

Pressure regulating valve:

 This unit is equipped with a pressure regulating valve which prevents damage to 

the unit by keeping the system pressure safely below a desired limit. When the system pressure exceed the 
setting of the valve spring, the fluid unseats the valves and bypasses to the reservoir. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

SAFETY FEATURES OF THE UNIT 

In case of EQUIPMENT FAILURE / BREAKDOWN turn the unit OFF an

d see “SERVICE / CARE 

RECOMMENDATIONS AND DIY TROUBLESHOOTING GUIDE

” section. 

 

Содержание HP201SAE
























Отзывы: