Spirax Sarco TVA DN100 Скачать руководство пользователя страница 46

Страница: 46 / 52

IM-P192-02

MI Issue 2

4.14.2 Alarm status register bit-fields:

Bit 1

Bit 0

State

Alarm code

Superheat

0x0000

Not applicable

Saturated

0x0002

Sub-saturated

0x0003

Bit

Set (1)

Cleared (0)

Bit 2 (0x0004) Pressure alarm is active

(too high or too low)

Pressure alarm is idle

Bit 3 (0x0008) Superheat margin active

Superheat margin idle

Bit 4 (0x0010)

Hi flow alarm is active

Hi flow alarm is idle

Bit 5 (0x0020)

Sensor constant alarm is active

Sensor constant alarm is idle

Bit 6 (0x0040)

No signal from sensor alarm is

active

No signal from sensor alarm is

idle

Bit 7 (0x0080)

Power failed (has been turned off

and on) alarm is active

Power failed alarm is idle

Bit 8 (0x0100)

Hi flow alarm has latched

Bit 9 (0x0200)

Sensor constant alarm has latched

Bit 10 (0x0400)

No signal from sensor alarm is

latched

Bit 11 (0x0800)

Power failed alarm has latched

nothing

Bit 12 (0x1000)

Low superheat (Low S-HT) alarm

Bit 13 (0x2000)

Over pressure alarm (OVEr PRES)

Bit 14 (0x4000)

Bit 15 (0x8000)

A maximum of 12 Modbus registers can be polled together at the same frame. It has to be

noted that only a poll with a valid start address and quantity that falls within the supported

outside this range or a frame that the start a quantity falls outside this range, the

TVA will reply with an 'illegal data address' error message. If the function code is incorrect,

it will reply with an 'illegal function' error message.

If a message is received with the wrong CRC, it will be ignored. The TVA response time is

not instant (look below) so wait for it to reply before asking for more data, otherwise it will

ignore new requests.

Содержание TVA DN100





















































Результаты поиска

Содержание TVA DN100

Отзывы:

Похожие инструкции для TVA DN100

Бренды по названию

Популярные бренды

Spirax Sarco TVA DN100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание TVA DN100

Отзывы:

Похожие инструкции для TVA DN100

Бренды по названию

Популярные бренды