Spirax Sarco SX75 Series Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 24

Spirax Sarco SX75 Series Скачать руководство пользователя страница 7

5

Selects the digit to be modified

(see enclosed leaflet)

In Manual operation, decrements the

value of main output Y1

Keys for

modifying

numeric

values of

any data

Increments the value of the flashing

digit, from 09

In manual operation increments the

value of main output Y1

Permits access to menu of functions

to be programmed

Keys for data

programming

and

processing

Enter or Scroll of values and modes

of operation

Change from Automatic to Manual operation and

vice versa

Set Point

Digit selection

Increment digit

Functions

Enter

Auto/Man

KEYS

1 Local + 4 storable used for:

modifying the Local Set point

to recall the Local operating Set point

recalling the 4 memorized Set points

(see enclosed leaflet)

1 Local + 1 Remote used for:

modifying the Local Set point

changing from Local to Remote Set point

and vice versa (see enclosed leaflet)

configuration:

1 Local used for:

modifying the Local Set point

2. FUNCTION OF KEYS AND DISPLAYS

«
...
5
6
7
8
9
...
»

Содержание SX75 Series

























Отзывы:

Нет отзывов