FCC STATEMENT:
This product complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference
that may cause undesirable operation. This equipment has been tested and found to comply with the limits for Class B digital devices
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference to radio
communications. Because this toy generates, uses, and can radiate radio frequency energy, if not installed and used in accordance
with the instruction, may cause harmful interference to radio communication. However there can be no guarantee that interference will
not occur. If this toy does cause interference to radio or television reception (you can check this by turning the toy off and on while
listening for the interference), one or more of the following measures may be useful:
• Reorient or relocate the receiving antenna
• Increase the separation between the toy and the radio or the TV
• Consult the dealer or an experienced TV-radio technician for help.
Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.
NOTE:
Changes, adjustments or modifications to this unit, including but not limited to, replacement of any transmitter component
(crystal, semiconductor, etc) could result in a violation of FCC rules under part 15 and/or 95 and must be expressly approved by
Spin Master Ltd or they could void the user’s authority to operate the equipment. Shielded cables must be used with this unit to insure
compliance with the Class B FCC limits.
CANADIAN Class B statement: This device complies with Industry Canada licence-exempt RSSs standard(s). Operation is
subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any
interference, including interference that may cause undesired operation of the device.
CAN ICES-3(B)/NMB-3(B)
POWER ADAPTER SAFETY INFORMATION
- The transformer is not a toy and should be connected to the wall outlet by an adult. It should be periodically examined for conditions
that may result in the risk of fire, electrical shock or injury to persons, such as damage to the cord, plug, blades, housing or other parts,
and in the event of such conditions, the transformer must not be used until the damage is repaired. The cord of this transformer cannot
be replaced; if the cord is damaged, dispose of the transformer in accordance with your local electrical product recycling regulations.
- Transformers and power supplies for toys are not intended to be used as toys, and the use of these products by children shall be
under the full supervision of parents.
- The toy must be used only with the recommended transformer.
- The toy is not to be connected to more than the recommended number of power supplies.
- Toys to be cleaned with a liquid are to be disconnected from the transformer before cleaning.
- To clean transformer, disconnect it from the wall and clean with a cloth dampened with water. Do not immerse in water or use
soap or other chemicals. Allow to dry before reusing. Do not connect to the AC outlet if wet or damaged.
- AC Adapter Electrical Ratings: US, CAN Input: ~ 120V AC, 60Hz, 300mA. UK Input: ~ 240V, 50Hz. Australia and New Zealand Input:
~ 240V, 50 Hz. Output: 9V DC, 700mA
- Batteries are only to be charged by adults or by children at least 8 years old.
This toy is equipped with LiPo and NiMH batteries. SPECIAL BATTERY INSTRUCTIONS:
- Never charge battery unattended.
- Charge battery in an isolated area. Keep away from flammable materials.
- Do not expose to direct sunlight. There is a risk of the batteries exploding, overheating, or igniting.
- Do not disassemble, modify, heat, or short circuit the batteries.
- Do not place them in fires or leave them in hot places.
- Do not drop or subject to strong impacts.
- Do not allow the batteries to get wet.
- Only charge the batteries with the specified Spin Master™ battery charger.
- Only use the batteries in the device specified by Spin Master™.
- Carefully read the instruction guide and use the batteries correctly.
- In the unlikely event of leakage or explosion use sand or a chemical fire extinguisher for the battery.
- Batteries must be recycled or disposed of properly.
Special Battery Removal Instruction for LiPO, NiMH:
Product Battery Removal Instructions: Internal battery is factory installed, product disassembly and battery removal must be performed
by an adult. Do not puncture, cut, tear, compress or deform product during disassembly. Ensure product is turned off, then use a
screw driver to remove all screws. Separate product body halves to expose internal electronics. When battery is visible in its entirety
use scissors to cut a single battery wire, immediately wrap the cut wire end with tape to isolate it, repeat until all battery wires are cut
and isolated, and the battery is free from the rest of the product. Dispose of battery in accordance with your local battery recycling or
disposal laws.
NOTE:
Opening of product and/or removal of battery will render product inoperative and voids manufacturer
warranties, dispose of remaining product components in accordance with local laws.
1
2
3
4
5
6
1
2
4
3
4
5
5
3
1. Clip the Remote Control to your side and
set to FOLLOW ME Mode.
2. Keeping controller around 5'-6'. Facing
BB-8 begin walking slowly.
3. BB-8 will move toward
the Remote Control.
1. Set the Remote Control to RC Mode.
2. Press the Animation Button once.
3. BB-8 will randomly animate.
4. Press and hold the Animation Button
for 2 seconds.
5. BB-8’s head will turn in the opposite direction.
6. The controls over BB-8 will reverse.
FOLLOW ME MODE
BB-8 may randomly display any of the following six moods:
BOLD; SAD; SASSY; HAPPY; SCARED; CURIOUS
BB-8 MOODS
RC/ ANIMATION BUTTON
1. After 3 - 5 minutes of no interaction, the Droid will go into SLEEP MODE. In SLEEP
MODE, say “
BB-8
” to reactivate the Droid. Press the Controller's Direction Knob OR
the Animation Button to reactivate.
2. After 5 minutes, the Droid will go into Power Down Mode.
3. Open both Charge Ports.
4. Move the Power Switches to the OFF Position.
5. Move the Power Switches back to the ON Position. Droid will re-activate.
SLEEP MODE
CAUTION:
Do not walk down stairs,
BB-8 will follow and
could get damaged.
NOTE:
Use the follow me mode only in large areas to avoid running into walls or other objects. If BB-8
stops moving towards your and begins to beep move closer so BB-8 can regain the remote
control IR LED signal. Make sure you do not cover the IR LED’s on the remote control.
10
11
