background image

Operation manual - Spider ILD01G 

 

26 / 54   

 

 

 

rev. 03-01-04-2019 

9.6 FUEL TANK 

The  plastic  fuel  tank  is  placed  on  top  of  the  mower 
deck, on one side of the mower. The tank has a screw-
on cap A.  

Before refuelling always stop the engine. Do not smoke 
or  approach  open  flames  or  sources  of  sparks  when 
manipulating with gasoline.                                        

Use unleaded 95-octane gasoline without any additives. 
The operator is responsible for all engine or fuel system 
damage resulting from the use of wrong, low-class, old 
or  contaminated  fuel.  The  warranty  does  not  extend  to 
such damage.

 

Do  not  fill  the  tank  near  open  flames  or  sources  of 
ignition.  

Do not smoke. 

 

Do not open the tank while it is hot.

 

Do not fill/empty the tank in enclosed areas.

 

9.7 PREPARING THE REMOTE RADIO CONTROLLER 

Insert the original battery (Ni-Cd 7.2V, 1500 mAh) into the remote radio controller. If the power indicator flashes, 
the battery is charged.

 

Discharge  signal 

–  if  the  voltage  of  the  remote  radio  controller  is  too  low,  then  the  RC  will  emit  a  high  pitch 

sound.  Move  the  mower  to  a  safe  place  and  replace  the  battery.  After  the  low  voltage  is  indicated,  you  have 
about 15 minutes to move the mower to a safe place. After 15 minutes the remote radio controller will be turned 
off permanently. If the battery is exhausted, replace it with a reserve battery.

 

 
 The transmitter (remote radio controller) and the receiver (control unit) were adjusted and set-
up  by  the  manufacturer.  Do  not  make any  modifications  to  these  devices.  They  are  a  matched 
pair.  

 

 

 

9.8 CHARGING THE REMOTE RADIO CONTROLLER BATTERY

 

To charge the battery: 
Connect the charger to the electric power outlet in your car. Insert the battery into the charger (orange lamp is 
illuminated, and the battery charging starts). 
When the battery is fully charged, the orange lamp flashes quickly. 
Leave the battery in the charger as long as necessary (the charger controls the charge level and does not 
overcharge the battery) 

 

 

 

 

 

 

 

 

Содержание ILD01 G























































Отзывы: