SPIDER 2SGS EFI Скачать руководство пользователя страница 52

Operation Manual 

 Spider 2SGS EFI

 

52 / 55 

rev. 01-01-02-2021 

 

 

13 MAINTENANCE AFTER SEASON 

When the season is over or if the machine is not going to be used for longer than 1 month, it is advisable to 
prepare it for storage. 

If fuel stays in a tank longer than 1 month without moving, it may create sticky sediment that can 
unfavourably affect the the whole fuel system and cause engine malfunction. 

 

Thoroughly clean the whole machine, especially the mowing mechanism. 

 

 

Replace damaged or worn-out parts 

 

 

Check all bolted connections. Tighten all loose nuts and screws. 

 

 

Lubricate all mobile parts 

– the whole machine (according to the lubrication plan) 

 

 

Empty the fuel tank and let the engine run until it runs out of fuel. 

 

 

When emptying the fuel tank, work in an open area outside. 

 

 

Prepare the engine for storage (according to the user’s manual of the engine) 

 

 

Disconnect the ignition cable. 

 

 

Unscrew the spark plug and pour a little oil into the cylinder bore (about 1 cm / 0,4 inch). 

 

 

Turn the engine by starting it shortly with the ignition key without spark plugs on. 

 

 

Screw the spark plug back hand tight. Do not connect the cable. 

 

 

Dismount the Accumulator and store it on the dry and warm place. 

 

 

Keep the mower on the save and dry place. Use the permeable cover to save the mower against the 
corrosion. 

Содержание 2SGS EFI
























































Отзывы: