background image

 

 

EBM30N/TEG 

 Installation and User Guide 

Document Number: 81773-4 

Issue: 2 

Spellman High Voltage Electronics Limited 

|

 

+44 (0)1798 877000

 

|

 

[email protected]

 

|

 

Broomers Park, Pulborough, W. Sussex, UK. RH20 2RY 

TEMPLATE: 40776 ISS A | ECN I-10067 | DATE: 16/04/21

 

QA/ENG/SAL

 

© 2021 Spellman High Voltage Electronics Corporation 

 

 

Page 13 of 16 

Protection 

All outputs are protected from arcs in the load and continuous short circuit.  

The unit will withstand maximum voltage arcs with an average repetition rate of up to 0.1Hz.  

If the Accelerator has more than 8 arcs in a nominal 10 second period the unit will shut down. If there 
are less than 8 arcs the unit will continue to operate. Arc events less than 100ms from the previous 
event will be ignored.  

A shutdown event maybe reset by toggling the ‘Outputs 1, 2&3 remote on/off’ level off and on again or 

toggling the input power off and on again. 

All low voltage inputs are protected against over voltage (up to 30V) and negative input voltages (up to 
-30V). 

The maximum output voltage, even under single fault conditions, is 40kV. 

Содержание EBM30N/TEG

















Отзывы: