background image

12

SPEKTRUM DX4S • TRANSMITTER INSTRUCTION MANUAL

EN

Timer 

The transmitter Timer can function as either an Up or Down Timer. 

Down Timer (default selection) 

The Down Timer allows you to adjust the amount of time in 10 second increments to a 

maximum of 21 minutes, which will then start a countdown to “0” once activated. The Down 

Timer value is normally the length of a race or vehicle run time. The Down Timer can be reset 

by selecting Timer Reset or by holding the switch that is assigned to that timer for 3 seconds.

Up Timer 

The Up Timer functions as a stopwatch and is useful for determining the available run time in 
one tank of fuel or a battery pack. 

Using the Timer

1. Assign the timer to a switch or button in the Switch menu.
2. To start or stop the timer, hold the assigned button.
3.  To reset the timer, press the timer button for more than 3 seconds.

Switch

The Switch menu enables you to assign any of the seven switches to one of 

the following functions. Switches that have a +/- next to the name can be 

assigned to different directions. For example, ST trim+ causes right steering 

trim to trim the steering to the right. ST trim- trims the steering to the left. 

Aux1 and Aux2 can only be assigned to one function at a time.  For example, 

if Aux1 is assigned to 4WS Mix, then it will not be available as an option on 
the switch screen.

Switch A, B, C, D and E

Inhibit

 – Switch off

AX1 Lin

 – Ch 3 Linear

AX1 2P

 – Ch 3 2-position

AX1 3P

 – Ch 3 3-position

AX1 MT

 – Ch 3 Momentary

AX2 Lin

 – Ch 4 Linear

AX2 2P

 – Ch 4 2-Position

AX2 3P

 – Ch 4 3-Position

AX2 MT

 – Ch 4 Momentary

ST Trim+

 – Steering Trim 

ST Trim-

 – Steering Trim

TH Trim+

 – Throttle Trim

TH Trim-

 – Throttle Trim

AX1 Trim+

 – Ch 3 Trim

AX1 Trim- 

– Ch 3 Trim 

AX2 Trim+

 – Ch 4 Trim

AX2 Trim-

 – Ch 4 Trim

Brake+

 – Full Brake Trim

Brake-

 – Full Brake Trim

ST Rate+

 – Steering Rate

ST Rate-

 – Steering Rate

ROSS

 – Remote Start

Timer 

– Up or Down Timer

4WS Mix

 – 4 Wheel Steer

BAK Mix

 – Brake Mix

Mix A 

– Mix A Function

Mix B

 – Mix B Function

Mix A Rate

 – Mix A Value

Mix B Rate

 – Mix B Value

 

Switch F

Inhibit
AX1 2P
AX1 MT
AX2 2P
AX2 MT
ROSS
Timer
4WS Mix
Mix A
Mix B

Dial

AX1 Lin
AX2 Lin
ST Trim+
ST Trim-
TH Trim+
TH Trim-
AX1 Trim+
AX1 Trim-
AX2 Trim+
AX2 Trim-

Brake+
Brake-
ST Rate+
St Rate- 

Содержание DX4S























Отзывы: