background image

 

 

 

 

 

 

 

 

    V1.0 Created on Apr 10

th

 

2013 

King Golden Ltd. 

Speed Passion Reventon Pro 1.1 - 2 cell LiPo User Manual 

Page 9 

11.

 

Programming the ESC 

 

Part Number 

Barcode 

Model 

SP000056 

4895135171390  Smart LCD Program Card 

 

The Smart Program card is an optional accessory which may be purchased separately. Programming 
the ESC is easy and fast with the pocket sized device. To change settings, plug the receiver wire from 
the ESC into the socket of the program card (the socket is on the left corner, and marked with

). 

Turn  on  the  ESC,  each  item’s  value  will  be  shown  on  the  program  card.  Use  “ITEM”  and  “VALUE” 
buttons  to  select  the  programmable  items  and  new  values,  and  press  the  “OK”  button  to  send  the 
new settings to the ESC. 

 

11.1 ESC PC Program Method and update ESC software: 

The Speed Passion Program Card is used to make all the adjustments to the active profile in the ESC. 
Any active profile can be modified via PC software with. 

i.

 

Connect the 

Speed Passion Smart Program Card

 to the Reventon ESC. 

Do not connect ESC 

with ESC fan and battery. 

 

ii.

 

Download Reventon PC Interface fro

www.speedpassion.net

. 

iii.

 

Install Reventon PC interface software. 

iv.

 

Install Reventon PC interface USB driver. (see Page 16 about steps of install the USB driver) 

v.

 

Connect the PC and 

Speed passion Smart Program Card

 by the USB Cable. 

vi.

 

Start Reventon PC Program. 

Содержание Reventon PRO 1.1
























Отзывы: