Spectrum Controls 1746sc-INI4i Скачать руководство пользователя страница 47

Страница: 47 / 56

Chapter 6: Testing Your Module

6-3

User’s Manual Pub. 0300266-04 Rev. A

Table 4-1 LED Definition

Use the following table to interpret LED indications:

If the module status

LED is…

And the channel status LED

is…

Then...

The channel is enabled.

Blinking

One of the following channel errors occurred:

•

Circuit open or no wiring is connected.

•

Signal is near or beyond end of range

•

Channel configured incorrectly

Refer to Troubleshooting.

Off

Either your module is powering up or the

channel is disabled.

Off

Either the power is off, the module is powering

up, or a module fault occurred. Cycle power. If

the condition persists, call your local distributor

or Spectrum Controls for assistance.

Section 6.5

Interpreting

I/O Error Codes

I/O error codes appear in word S:6 of the SLC processor status file. The first two

digits of the error code identify the slot (in hexadecimal) with the error. The last

two digits identify the I/O error code (in hexadecimal).
The error codes that apply to your module include (in hexadecimal):

•

50–5E

•

71 (watchdog error)

•

90–94

For a description of the error codes, refer to the

Allen-Bradley Advanced

Programming Software (APS) Reference Manual

, Allen-Bradley publication

1746-6.11.

Содержание 1746sc-INI4i

























































Результаты поиска

Содержание 1746sc-INI4i

Отзывы:

Похожие инструкции для 1746sc-INI4i

Бренды по названию

Популярные бренды

Spectrum Controls 1746sc-INI4i, Руководство пользователя

Результаты поиска

Содержание 1746sc-INI4i

Отзывы:

Похожие инструкции для 1746sc-INI4i

Бренды по названию

Популярные бренды