Spectrum Controls 1746sc-INI4i Скачать руководство пользователя страница 15

Страница: 15 / 56

User’s Manual Pub. 0300266-04 Rev. A

Chapter 2

Installation and Wiring

This chapter will cover:

•

Avoiding electrostatic damage.

•

Determining power requirements.

•

Selecting a rack slot.

•

Inserting your module into the rack.

•

Wiring your module.

NOTE

Although your module has a jumper on its printed circuit board, this

jumper is for the manufacturer’s use only. Your module was calibrated by

the manufacturer, so no further calibration is required.

NOTE

For UL and CUL compliance, power and input/output (I/O) wiring must

be in accordance with Class I, Division 2, wiring methods [Article 501-4

(b) of the National Electrical Code, NFPA 70] and in accordance with the

authority having jurisdiction. Also, you must observe the warnings shown

below. Failure to observe these warnings can cause personal injury.

WARNING

EXPLOSION HAZARD

•

Substitution of components may impair suitability for Class I,

Division 2.

•

Do not replace components or disconnect equipment unless power

has been switched off or the area is known to be non-hazardous.

Touch a grounded object to discharge static potential.

•

Do not connect or disconnect components unless power has been

switched off or the area is known to be non-hazardous.

•

This product must be installed in an IP54 rated enclosure that

requires a tool to open.

•

All wiring must comply with N.E.C. article 501-4(b).

The following documents contain information that may help you as you install

and wire your module:

•

National Electrical Code

, published by the National Fire Protection

Association of Boston, MA.

•

IEEE Standard 518-1977,

Guide for the Installation of Electrical

Equipment to Minimize Electrical Noise Inputs to Controllers from

External Sources.

•

IEEE Standard 142-1982,

Recommended Practices for Grounding of

Содержание 1746sc-INI4i

























































Результаты поиска

Содержание 1746sc-INI4i

Отзывы:

Похожие инструкции для 1746sc-INI4i

Бренды по названию

Популярные бренды

Spectrum Controls 1746sc-INI4i, Руководство пользователя

Результаты поиска

Содержание 1746sc-INI4i

Отзывы:

Похожие инструкции для 1746sc-INI4i

Бренды по названию

Популярные бренды