SpectraPure Mega MaxCap Скачать руководство пользователя страница 4

Страница: 4 / 28

SpectraPure

Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

SYSTEM SPECIFICATIONS:

Sediment Prefilter

0.5 micron sediment prefilter (SF-MT-0.5-10)

Carbon Filter

0.5 micron carbon block prefilter (CF- 0.5-10)

RO Membrane Type

90 GPD SpectraSelectPlus™ TFC Membrane

(Use 2 for 180 GPD Systems)

DI Cartridges

Mega MaxCap™ Extended Life DI Cartridge (DI-MMC-10)
Enduro DI™ DI Finishing Cartridge (DI-MB-ENDI-10)

Rejection Rate

Typical stabilized conductivity rejection 99%
Minimum conductivity rejection 98%

Input Water Pressure

60 psi (4.15 bar) line pressure*

Input Water Temp

77°F (25°C)

Recovery Rate

33% (i.e. 33% of the water will be collected as pure water)

Dimensions:

MMC-RODI-90-10-MF

21" W x 15" H x 7" D (One Membrane)

MMC-RODI-180-10-MF

21" W x 15" H x 7" D (Two Membranes)

Nominal Membrane Flow Rates @ 60 psi, 77° F, & 250 ppm TDS :

GPD

Product Water Flow Rate

Concentrate Flow Rate (2:1)

237 ml/min

473 ml/min

180

473 ml/min

946 ml/min

Permeate flow and TDS rejection is based on the following test conditions:
250 ppm softened tap water, 77° F (25° C), 33% recovery and 60 psi.

Higher TDS, harder tap water, lower water temperature, greater recovery rate, or lower
operating pressure may contribute to reduced permeate flow and/or lower TDS rejection.

Reverse Osmosis Operating Limits:

Operating Pressure*

40 – 80 psi (2.75 – 5.5 bar)

pH Range

2 – 11

Maximum Temperature

113° F (45° C)

Maximum Turbidity

1.0 NTU

Maximum Silt Density Index

5.0 (based on 15 min. test time)

Free Chlorine Tolerance

less than 0.1 ppm

Maximum Iron

less than 0.1 ppm

Maximum Manganese

less than 0.1 ppm

Maximum Hydrogen Sulfide

0 ppm

*Operating pressure less than 40 psi may require a booster pump:
Operating pressure greater than 80 psi may require a pressure regulator.

Содержание Mega MaxCap





























Результаты поиска

Содержание Mega MaxCap

Отзывы:

Похожие инструкции для Mega MaxCap

Бренды по названию

Популярные бренды

SpectraPure Mega MaxCap, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Mega MaxCap

Отзывы:

Похожие инструкции для Mega MaxCap

Бренды по названию

Популярные бренды