manualshive.com logo in svg

SpectraPure Eliminator RO 100-LP, Инструкция по установке и эксплуатации

Поделиться
Скачать
SpectraPure Eliminator RO 100-LP Скачать руководство пользователя страница 4

SpectraPure

®

SpectraPure

®

Inc.

  

480.894.5437   Call us toll-free  1.800.685.2783    

2167 East Fifth St,    Tempe, Arizona   85281

4

SYSTEM SPECIFICATIONS:

Sediment Prefilter

1 micron sediment prefilter

Carbon Filter

1 micron carbon block prefilter

RO Membrane Type

Thin-Film Composite  (TFC)

Rejection Rate

98% average

Input Water Pressure

60 psi (4.15 bar) line pressure*

Input Water Temp

77°F (25°C)

Typical Membrane Rejection

98%

Dimensions:

 

Elim RO 100, Elim RO 200

16" H x 15" W x 7" D  (One Membrane)

Elim RO 400

17.5" H x 15" W x 7" D  (Two Membranes)

Permeate flow and TDS rejection is based on the following test conditions:
250 ppm softened tap water, 77° F (25° C), 15% recovery and 60 psi.
Higher TDS, harder tap water, higher temperature, greater recovery rate, or 
lower operating pressure may contribute to reduced permeate flow and/or 
lower salt rejection.

Reverse Osmosis Operating Limits:

Operating Pressure*

40 – 80 psi (2.75 – 5.5 bar)

pH Range

2 – 11

Maximum Temperature

113° F (45° C)

Maximum Turbidity

1.0 NTU

Maximum Silt Density Index

5.0 (based on 15 min. test time)

Free Chlorine  Tolerance

less than 0.1 ppm

Maximum Iron

less than 0.1 ppm

Maximum Manganese

less than 0.1 ppm

Maximum Hydrogen Sulfide

0 ppm

*Operating pressure less than 40 psi may require a booster pump:
  Operating pressure greater than 80 psi may require a pressure regulator.

SpectraPure

® 

Inc

.

 Assumes no responsibility for water  

damage due to leaks. It is the user’s responsibility to determine 

that the system is leak-free.

Содержание Eliminator RO 100-LP

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды