background image

Copyright © SpectraDynamics, Inc.   2010

 

 

 

 

The  HPDA-15RM-C  is  warranted  to  be  free  of  defects  under  normal  operating 
conditions,  as  specified,  for  one  year  from  date  of  original  shipment  from 
SpectraDynamics,  Inc  (SDI).   

SDI’s  obligation  and  liability  under  this  warranty  is 

expressly limited to repairing or replacing, at 

SDI’s option, any product not meeting the 

said  specifications.    This  warranty  shall  be  in  effect  for  one  (1)  year  from  the  date  a 
HPDA-15RM-C  is  sold  by  SDI.    SDI  makes  no  other  warranty,  express  or  implied,  and 
makes no warranty of the fitness for any particular purpose. 

SDI’s obligation under this 

warranty  shall  not  include  any  transportation  charges  or  costs  of  installation  or  any 
liability  for  direct,  indirect,  or  consequential  damages  or  delay.  Any  improper  use, 
operation beyond capacity, substitution of parts not approved by SDI, or any alteration or 
repair by others in  such manner as in  SDI’s reasonable  judgement affects the product 
materially and adversely shall void this warranty.  No employee or representative of SDI 
is authorized to change this warranty in any way or grant any other warranty. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

SDI

 

Warranty 

SDI

S

PECTRA

D

YNAMICS

,

 

I

NC

  

  

1849 Cherry St. Unit 2.

  

  

Louisville, CO 80027

  

 

  

Phone: (303) 665-1852

  

 

  

Fax: (303) 604-6088

 

Se habla español 

 

Содержание HPDA-15RM-C













Отзывы: